User manual FUTABA MC330R

[. . . ] 1M23N08204 Before using your MC330CR, please read this manual thoroughly and use the MC330CR properly and safely. After reading this manual, store it in a safe place. MOUNTING PRECAUTIONS Install the receiver and receiver antenna at least 1cm away from the amp, motor cord, power cord, Nicd battery, and other parts that carry a high current. Metal and carbon chassis and other conductive parts transfer switching noise. [. . . ] (Black) is minus. When making adjustments, remove the motor, or place the model on a stand, so that it cannot run. (Red) Miniature screwdriver When going to and returning from the circuit, and when storing the model, always remove the Nicd battery. If the switch is turned on erroneously, control may be lost or a fire may start. MC330CR Power switch [MC330CR Technical Data] Accessory. Use to press the pushbutton switch. Receiver connector Connects to the receiver throttle channel. Special Markings Pay special attention to the safety at the parts of this manual that are indicated by the following marks. Mark (Specifications are subject to change without prior notice. ) ·Operating system: Forward, reverse, and brake operations are all linear. ·Power requirement: Nicd battery 6~7 cells (7. 2~8. 4V) ·PWM frequency: 1. 5kHz (fixed) ·Setting: One-touch input by pushbutton switch. ·Current capacity (FET rating): Forward=200A, reverse=100A ·Case size: 27. 1x333x12. 8mm (excluding protruding parts) ·Silicon cord gauge size: AWG14 equivalent ·Weight: 45g (including connectors and switches) ·BEC voltage: 6. 0V Symbol: ; Prohibited ; Mandatory Meaning Procedures which may lead to a dangerous condition and cause death or serious injury to the user if not carried out properly. Procedures which may lead to a dangerous condition or cause death or serious injury to the user if not carried out properly, or procedures where the probability of superficial injury or physical damage is high. Procedures where the possibility of serious injury to the user is small, but there is a danger of injury, or physical damage, if not carried out properly. SET UP Neutral, high, and brake MAX points setting Set the steering angle adjustment function (ATV) to 100% and the ABS function and acceleration function to OFF using the transmitter throttle channel function. If the steering angle is too large or the ABS and acceleration functions are on, erroneous operation may occur. *When using the ABS function, after setting up the MC330CR, stop the reverse function, then turn on the ABS function. If the ABS function is on, the MC330CR cannot be set up correctly. PROTECTION CIRCUIT OPERATION The following protection circuits are built into the MC330CR. When a protection circuit operates, remove the cause before operating the model again. Overcurrent protection Heat protector Low voltage operation When an overcurrent flows due to an output short circuit, etc. , the overcurrent protection circuit automatically limits the current to protects the FET. is detected, the heat protector operates so that the speed is gradually reduced. When the FET temperature drops, the heat protector automatically resets. However, remove the cause of the overheating before operating the model again. When the Nicd battery voltage drops, this function limits the motor output current and ensures steering operation. [. . . ] (Brake operation only) (Pushbutton switch operation) (Power switch) *Becomes brighter nearer the brake MAX point. 1 Reverse function cancellation While pressing the pushbutton switch, ON set the power switch to ON. * When desired, you can enable the cancelled reverse function by repeating the operation shown at the left. (The reverse function is switched alternately. ) (Amp power left on alarm) Blinks. *When the transmitter if OFF, this function is not performed in environments such that the servo operates erroneously. When the transmitter power was turned off first. BRAKE/REVERSE OPERATING INSTRUCTIONS Operation can be switched to reverse operation by returning the throttle trigger (or throttle stick) from the brake position to the neutral position. FUTABA CORPORATION * Confirmation beep only sounds when the motor was connected. Makuhari Techno Garden Bldg. , B6F 1-3 Nakase, Mihama-ku, Chiba 261-8555, Japan Phone: (043) 296-5118 Facsimile: (043) 296-5124 ©FUTABA CORPORATION 2000, 7 [. . . ]