User manual GE SECURITY NX-148_E REV A

[. . . ] NX148-E LCD KEYPAD TABLE OF CONTENTS GLOSSARY OF TERMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 UNDERSTANDING THE LIGHTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 KEYPAD FUNCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 ARMING YOUR SYSTEM IN THE "AWAY" MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Entering a code followed by the [CANCEL] key during or after an alarm report to the central station will cause the cancel light to come on. It will stay on until the central station has received the cancel report. NOTE: The cancel feature must be enabled. BYPASSING ZONES If you wish to bypass one or more zones, this must be done while the system is in the disarmed state. If the zone is not known, refer to Procedure #2. Procedure #1 Step 1 Step 2 Step 3 Step 4 If you know the number of the zone to bypass, use the following: Press the [BYPASS] key. When the LCD prompts for a code (optional, if programmed), enter your user code. (Example: Press 6 1 1 2 for zone 112. ) for zone 6 or Step 5 Step 6 Step 7 Press the [BYPASS] key again. Press the # key to exit this viewing mode. 8 Procedure #2 Step 1 Step 2 Step 3 Step 4 If you do not know the number of the zone you wish to bypass, use the following steps: x The description for zone 1 will be displayed. Press U Use the x y scroll keys to browse through the custom descriptions for the zones in this system. To bypass or unbypass a specific zone, press the [BYPASS] key while that zone is displayed. When finished, press the # key to return to the code entry screen. GROUP BYPASS By pressing the [BYPASS] key, followed by the 0 key, then the [BYPASS] key again, all zones that are designated as group bypass zones will be bypassed. Press the [BYPASS] key again to exit group bypassing. UNBYPASSING To manually unbypass zones, perform the bypassing procedure on a zone that is already bypassed. NOTE: All zones will automatically be unbypassed each time the system is disarmed. EMERGENCY ACTIVATION KEYS NOTE: You must press and hold these keys for 2 seconds to activate these functions. Your system may not be programmed for these activations. Fire Key - If programmed, you can activate the Fire alarm by pressing the Emergency Activation [Fire] key for two seconds. If your system is connected to a monitoring center, an emergency report could be sent to that center. This key should only be pressed in an emergency situation requiring response by fire department personnel. 9 Auxiliary Key - If programmed, you can activate the auxiliary alarm by pressing the Emergency Activation [Auxiliary] key for two seconds. If your system is connected to a monitoring center, an emergency report could be sent to that center. This key should only be pressed in an emergency situation requiring response by emergency personnel. Police (Panic/Hold-Up) Key - If programmed, when the Emergency Activation [Police] key is pressed for two seconds, a local audible alarm will sound. If your system is connected to a monitoring center, an emergency report could be transmitted to that center. These keys should only be pressed in an emergency situation requiring immediate response by law enforcement personnel. NOTE: Some Panic/Hold-Up alarms are programmed to be silent at the protected site while reporting an alarm to the monitoring center. Check with your installing company to determine how your security system will respond to the Panic/Hold-Up activation. FUNCTION MENU The functions listed below are found in the Function Menu. Step 1 Press U The display will now begin scrolling though a list of functions and the corresponding numbers associated with those functions. [. . . ] Call your service provider promptly if this message is observed. 6HUYLFH5HTXLUHG 7\SHUIRUKHOS 2 . One or more of the following fault If you see this display, press U messages will be displayed. To exit the service messages, press [#]-[#]. &RQWURO %R[WDPSHU &RQWURO )DLOWR&RPP &RQWURO *URXQGIDXOW &RQWURO /RVVRIWLPH &RQWURO /RZ%DWWHU\ &RQWURO 2YHUFXUUHQW &RQWURO 3KRQHWURXEOH &RQWURO 3RZHUWURXEOH &RQWURO 6LUHQWURXEOH (Optional) The Box Tamper circuit has activated. The control attempted to communicate a message to the Central Station, but was unsuccessful. [. . . ]