User manual GE SECURITY NX-6 REV B

[. . . ] For the latest documentation, contact your local supplier or visit us online at www. gesecurity. com. This publication may contain examples of screen captures and reports used in daily operations. Any similarity to names and addresses of actual businesses or persons is entirely coincidental. Trademarks and patents GE and the GE monogram are registered trademarks of General Electric Company. Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products. [. . . ] Feature must be programmed by the installer. Motions Doors + Windows and Motions Disarm Chime Special chime Trouble beeps No activity beeps a a. This feature is not verified for use by UL. Chapter 3 How your system communicates 21 Alarm sirens and lamp modules Exterior and interior sirens make three different alarm sounds on the premises, each indicating a different type of alarm. Sirens are programmed by the installer to time out and stop sounding after a specified time. Use Table 8 to understand the siren sounds used by the security system. Table 8. Alarm Siren and X10 Light Information Function X10 lights a Fire Steady Steady Temporal 3 b Temporal 3 b Intrusion Flashing Steady Steady Steady Emergency Steady Alarm beeps Fast on/off X10 siren a Interior and panel siren Exterior siren a. Temporal 3 refers to a continuous pattern of three siren pulses, then off for 1. 5 seconds, three siren pulses, then off for 1. 5 seconds. 22 Simon XT User Manual Panel indicator lights Use Table 9 to understand the panel indicator lights. Table 9. Panel indicator lights Button DOORS+WINDOWS MOTIONS DISARM STATUS Enter Chime - Solid bell Special chime - Outlined bell Light schedules - Clock Sensor lights - Light bulb Latchkey on - Key a. When button light is on Doors + Windows armed Motions armed System disarmed System trouble, open sensor, or bypassed sensor There are no open sensors Door will cause chime Motion will cause chime Time-activated lights feature enabled Sensor-activated lights feature enabled Latchkey feature enabled a When the button flashes Doors + Windows armed and no entry delay on Motion sensors armed and latchkey on System subdisarmed System in alarm Latchkey feature (for MOTIONS button light flashes, light schedules, sensor lights, and latchkey indication) is not verified for use by UL. Chapter 3 How your system communicates 23 Trouble beeps Your security system is able to automatically test itself for: · · · · Power failures Low batteries Nonworking sensors Communication troubles with the central monitoring station When your security system detects one of the problems above, six rapid beeps sound every minute until the trouble condition is corrected. To stop the trouble beeps, press STATUS or arm/disarm the system while the trouble condition exists. Trouble beeps will resume four hours later unless the trouble condition is corrected. The following list explains the trouble beep conditions: AC power failure. This condition (if programmed by installer) occurs if your security system has been accidentally unplugged or if there has been an AC power outage. Any status lights go out immediately, and trouble beeps start after five minutes. The system will call to notify the central monitoring station about this problem. Some types of status conditions, such as the alarm history, must be cleared manually. To clear system status, press the STATUS button, read and/or listen to the status messages, then press DISARM. If the trouble condition was a low system battery, perform a sensor test. The STATUS light should turn off if all trouble conditions have been corrected. Chapter 4 Programming This chapter describes how to program your system. It will guide you through programming instructions for system features. . 35 26 Simon XT User Manual System menu Your Simon XT self-contained security system security system allows you to program certain user options, such as access codes, time schedules, or the system time. These options are accessed through a system menu. Entering and exiting the system menu To enter the system menu, press the scroll up/down buttons or the Enter button in the upper right of the panel. Press STATUS to exit a menu or option edit mode and navigate up one level. The panel automatically exits the system menu after a few seconds of inactivity if no access code has been entered yet. After an access code has been entered to access a codeprotected area of the system menu, the timeout is 30 seconds (4 minutes while performing a sensor test). Code options The Simon XT security system provides a system of codes to be entered when a certain level of authority is required to perform an action. [. . . ] 24 sensor tampered. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 set clock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 silent exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]