User manual GE SECURITY RANGER 8600E REV A

[. . . ] (This is a phone command only. ) Check Alarm Memory xxxix Contents Getting to Know Your Security System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Communicating with the Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Instructing the Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Enter the programming menus by pressing 9 + System or Partition Master Code. Enter the System or Partition Master code, then . , + 6 + to exit the programming menus. Assigning the System Test Attribute System Tests is a user code attribute that allows the user to perform system tests. If the user code does not have this attribute turned on, the user will not be able to perform phone or sensor tests. Enter the programming menus by pressing 9 + System or Partition Master Code. To turn System Testing off, press 1 + . , + 6 + to exit the programming menus. , + 6 + to exit the programming menus. 12 SETTING THE TIME AND DATE Although the installer usually sets the time and date at the time of installation, the user can change it when necessary. See Appendix C, "Programming Your System" for more detailed information on setting this feature. Enter the programming menus by pressing 9 + System or Partition Master Code. Enter the programming menus by pressing 9 + System or Partition Master Code. 3. Enter the programming menus by pressing 9 + System or Partition Master Code. Press , + 6 + to exit the programming menus. 4. Adjusting the Touchpad Display Brightness You may want to change the brightness of a touchpad display based on its location in a building or room. For example, dim the touchpad display in a bedroom or enhance a display near a window. Enter 2 to include the day in the schedule ("ON") or 1 to exclude the day from the schedule ("OFF"). Press to secure your choice. Example 2 of One Day Rollover. Building on Example 1, let's say that you'd like the front entry light to be on between 10 p. m. By simply applying the start and stop times to each day, one time schedule can cover the entire week. S ch e d u le X S ta rt S to p M on Tue W ed Thur F ri Sat Sun P a rt. 2 2 :0 0 0 5 :0 0 ON ON ON ON ON OFF OFF 1 4. 8. Multiple Day Rollover The simplest method for defining a window of time that spans multiple days is to use 99:99 to signify an open start or stop time. 9. 1= 2= O ff On Example of Multiple Day Rollover. At your business you'd like specific lights to remain lit from Friday afternoon through the weekend until Monday morning. In this situation, the lights need to be scheduled to roll over until they reach a recognizable stop time. Since S ch e d u le S ch e d u le the stop time is 99:99, the lights will remain Y Z lit (roll over) until a recognizable stop time is 9 9 :9 9 S ta rt 1 6 :0 0 reached. 0 5 :0 0 9 9 :9 9 S to p Schedule Z is set up with an undefined start ON OFF time (99:99), so if the lights were already lit, M o n they will remain lit until the Schedule Z stop time is reached at 5 a. m. Tue W ed Thur F ri Sat Sun P a rt. 10. Press B to move to the next day of the week or press , to return to the schedule list. Press , + 6 + to exit User Programming. Scheduling Consecutive Days There may be instances when you'd like to schedule a feature event to start one day and stop the next day or a number of days later. One Day Rollover You can create a schedule that begins on one day, and stops the next day by using only one time schedule. (The stop time must be within 24 hours of the start time. ) OFF OFF OFF ON OFF OFF 1 OFF OFF OFF OFF OFF OFF 1 Example 1 of One Day Rollover. At home you'd like the front entry light to be on from 10 p. m. By taking advantage of One Day Rollover, one time schedule can cover both days. [. . . ] "USER 04 -- Press , + B to move to the next user code, or , + 6 + to exit the programming menus. Enter the programming menu by pressing 9 + System or Partition Master Code. Press B until the touchpad displays "USER CODES, " then press . The touchpad displays "REGULAR USER CODES. " Press B until the display reads "PARTITION MASTER CODE, " then press . [. . . ]