User manual HAMA BLUETOOTH-HEADSET TATTOO DRIVER PACK QUICK GUIDE

[. . . ] When fully charged (about 6. 5 hours), the charging battery indicator light turn off. 4 START BLUETOOTH FEATURE Your Phone Your phone's Bluetooth feature is off by default. To use your headset, you must turn on the Bluetooth feature in your phone. For most Motorola phones (at the main menu): 1 Press (Menu) > Settings > Connection >Bluetooth Link > Setup. The Bluetooth feature remains on until you turn the feature off. Note: These steps are for most Motorola phones. [. . . ] The Bluetooth feature remains on until you turn the feature off. Note: These steps are for most Motorola phones. For other phones, see your phone's user's guide. 5 PAIR Your Headset Before you can use your Headset, you must pair (link) it with your phone. Step A - ENSURE HEADSET IS IN PAIRING MODE Power on headset by removing from charger base. After a few moments, the indicator light will be steadily lit in blue to indicate headset is in pairing mode. Indicator Light (steadily blue for pairing mode) If the headset does not enter pairing mode, see TROUBLESHOOTING for help. 6 PAIR Continued Your Phone Step B - SET YOUR PHONE TO LOOK FOR YOUR HEADSET For most Motorola phones: 1 On your Motorola phone, press (Menu) >Settings > Connection > Bluetooth Link >Handsfree > Look for Devices. Enter the passkey: 0000 Select OK. When your headset successfully pairs and connects with your phone, the indicator light changes from steadily lit to flashing blue. Note: These steps are for most Motorola phones. For other phones, see your phone's user's guide. 7 TEST AND USE Your phone and headset are now paired and ready to make and receive calls. The eartip should be inserted so that the headset feels comfortable and forms a seal in the ear. Note: See " Eartips and Your Headset" on the reverse side of this guide for more information on using eartips with your headset. 2 On the phone, dial the number you want to call and press Send key on your phone. 3 If your phone and headset are successfully paired, you will hear ringing on the headset. After you have successfully paired your phone and headset, you don't need to repeat these steps. Tap the Call button Press and hold the Call button until you hear a low beep Tap both Volume buttons Press and hold both Volume buttons until you hear a low beep Note: Some features are phone/network dependent. 17 AUDIO TONES The audio tones provide information about your headset status. Audio Tone Single high tone when pressing volume button Five rapid high tones repeated every 20 sec. No audio indications; detereriorating quality Ring tone Single very high tone Single high tone Headset Status Volume at minimum or maximum Low battery Out of range Incoming call All calls ended Tapping Call button or both volume buttons 18 AUDIO TONES CONTINUED Audio Tone Single medium tone Single low tone Headset Status Pressing Call button or both Volume buttons for 1-2 sec Pressing and holding Call button or both Volume buttons for greater than 2 secs. Phone network not available Mute enabled Mute disabled Headset powering on Headset powering off Single high tone repeated every 5 sec Two ascending tones Two descending tones Four ascending tones Four descending tones 19 INDICATOR LIGHTS Indicator lights provides information about your headset and charger base status. Charger Base Indicator Charger Battery ( ) Headset Battery ( ) Headset Indicator Off On (steady) 10 rapid flashes Slow pulse Quick flash Status Power off Pairing mode Pairing successful Connected (on a call) Standby ( not on call) Status (On) Charging (Flashing) Battery low (Off) charging complete (On) Charging (Off) charging complete Note: After 5 minutes of inactivity, the light stops flashing to conserve power, but the headset remains in standby mode. 20 TROUBLESHOOTING My headset will not enter pairing mode. Make sure that any devices previously paired with the headset are turned off. If the indicator light is not steadily lit in blue, turn off both the other device and headset, wait 10 seconds, then turn headset back on. Wait for the indicator light to become steadily lit in blue, indicating the headset is now in pairing mode. Make sure the indicator light on your headset is on (lit in blue) and steady when your phone is searching for devices (see step 3). Make sure your phone is on and the Bluetooth feature is turned on in your phone (see step 2). [. . . ] Wait for the indicator light to become steadily lit in blue, indicating the headset is now in pairing mode. Make sure the indicator light on your headset is on (lit in blue) and steady when your phone is searching for devices (see step 3). Make sure your phone is on and the Bluetooth feature is turned on in your phone (see step 2). If the Bluetooth feature was turned off or was turned on only temporarily, you may need to restart the Bluetooth feature (see step 2) and pair your phone and headset again (see step 3). 21 SUPPORT If you need more help, contact us at 1- 877-MOTOBLU or visit us at www. hellomoto. com/Bluetoothsupport Motorola, Inc. [. . . ]