User manual HP PROCURVE 1810-48G J9660A

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual HP PROCURVE 1810-48G J9660A. We hope that this HP PROCURVE 1810-48G J9660A user guide will be useful to you.


HP PROCURVE 1810-48G J9660A : Download the complete user guide (1199 Ko)

Manual abstract: user guide HP PROCURVE 1810-48G J9660A

Detailed instructions for use are in the User's Guide.

[. . . ] HP 1810 Switches Management and Configuration Guide HP 1810 Switches September 2012 Management and Configuration Guide © Copyright 2012 Hewlett-Packard Development Company, L. P. This document contains proprietary information, which is protected by copyright. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of Hewlett-Packard. Disclaimer The information contained in this document is subject to change without notice. HEWLETT-PACKARD COMPANY MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. [. . . ] This feature is disabled by default. LED intensity Configuration LED Intensity Intensity Level Start Time Duration Recur Daily Enable LED intensity control globally on all ports. Specifies the time of day when the configured LED intensity level is activated. Valid values are any hour or half-hour from midnight (12:00 AM) through 11:30 PM. Specifies the number of hours the configured LED Intensity level is in effect. Specifies whether the LED intensity settings are in effect one time only, or daily. Default value is Yes. Click Apply to save any changes for the current boot session; the changes take effect immediately. 4-7 Switching Pages Loop Protection Loop Protection Loops in a network can consume switch resources and degrade performance. The HP 1810 series switch software provides an automatic Loop Protection feature. Loop Protection may be enabled or disabled globally and on a port-by-port basis. When enabled globally, the software sends loop protection packets to a reserved layer 2 multicast destination address on all the ports on which the feature is enabled. Transmission of the packet can be disabled selectively on certain ports, even when Loop Protection is enabled. If this multicast packet comes back to the switch with any of the ports’ MAC addresses as the source, the switch determines that a loop has occurred. The port that received the loop protection packet from the switch can be shut down for a configured period, or a log entry can be made. Ports on which Loop Protection is disabled drop the loop protection packets silently. To display the Loop Protection configuration page, click Switching > Loop Protection in the navigation pane. Loop Protection 4-8 Switching Pages Loop Protection Table 4-6. Loop Protection Fields“ Field Loop Protection Transmission Time Shutdown Time Loop Protection Select Description Enable this feature globally. Enter the time interval, in seconds, between sending Loop Protection packets. Set the number of seconds that a port remains shut down if a loop has been detected on the port. Select how you want to configure Loop Protection: • All— Enables all interfaces with Loop Protection. • One by One— Enables you to configure Loop Protection on ports individually (default). If Loop Protection is enabled on a port, select one of the following actions to occur when a loop is detected: • Log— The event is logged and the port remains operational. • Shutdown port— The port is shut down for the configured period. [. . . ] Note that, in this example, the image was downloaded as the inactive (backup) image. To complete the update process and to activate the backup image as the operating software, use the Dual Image Configuration page. In the following example, Image1 is the active image, and Image2 is the newly updated backup image. By clicking Activate, Image2 will be activated on the next reboot (and Image1 will become the inactive backup image). 10. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE HP PROCURVE 1810-48G J9660A




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual HP PROCURVE 1810-48G J9660A will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.