User manual INDESIT B33FNFUK

[. . . ] That the washing machine is levelled properly; something worth checking to aid the performance of your washing machine; 4. That the drum's fixing screws have been removed from the back of the washing machine; 2. 12) With just a bit of care, it will repay you with loyalty and devotion. With the necessary upkeep, it will wash for years and years to come. A correct distribution of your laundry is vital to the successful outcome of the wash and the life of the washing machine. [. . . ] SAVE detergent, time, water and between 5 to 15% energy consumption by NOT selecting Prewash for slight to normally soiled laundry. Pretreat stains with stain remover or soak dried in stains in water before washing to reduce the necessity of a hot wash programme. SAVE energy and time by selecting the highest suitable spin speed to reduce the water content in laundry before using a drying programme. 7 Instructions for installation and use Troubleshooting Before calling, read the following In most cases, when your washing machine fails to work, the problems arising can be easily solved without having to call for a technician. The washing machine fails to start. Is the plug correctly inserted into the socket?A circuit breaker may have switched off as a result of too many electrical appliances working at the same time. For safety reasons, the washing machine cannot work if the door is open or not shut properly. Is the programmed start knob, in the correct position for those models concerned?For safety reasons, if the washing machine does not load water, it cannot start a wash cycle. If the knob continues to turn, call for assistance because it is showing an anomaly. But where did all the water go? Simple: with the new Indesit technology, you need less than half of it, to get good results on twice as much!This is why you cannot see the water through the door: because there is little, very little of it, to respect the environment yet without renouncing maximum cleanliness. And, on top of that, you are also saving electricity. The washing machine fails to fill with water. RIGHT Turn off the water supply after use. compliance with IEC regulation 456 This appliance conforms with the following E. E. C. directives: - 73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications - 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications 9 Instructions for installation and use Installation and removal When the new washer arrives Whether new or just transported to a new house, installation is extremely important for the correct functioning of your washing machine. After removing the appliance from its packaging, check that it is intact. The inside of the machine is supported, for transportation, by 3 screws on the back panel. Connection to the water mains Both hot and cold water supplies are preferable and they should be between 34. 5kN/m²(5lb/in²) and 1034. 2kN/m² (150lb/in²) pressure. The hose having the red end fitting should be encountered between the hot supply and the threaded connection adjacent to the letter H on the rear of the machine. The hose having the white end fittings should be connected between the cold supply and the threaded connection adjacent to the letter C on the rear of the machine. Remember to insert a sealing washer at each connection to ensure watertight joints. Do not overtighten the connections by using tools -hand tight is sufficient to prevent leaks. It is generally more convenient to have these supplies away from the sink taps. Where no suitable hot water supply is available or it does not meet these requirements, both inlet hoses may be connected to a cold supply by using two taps etc. , or a «T» junction on the plumbing however, use of cold water only will increase programme times. Note: the maximum temperature should not exceed 70°C (158°F). Connecting the drain hose The drain hose (hooked pipe) is secured to the rear of the machine by support clips and may be routed to right or left as required. Electric connection Your appliance is now supplied with a 13 amp fused plug it can be plugged into a 13 amp socket for immediate use. [. . . ] Attention: Before attempting to examine this pre-chamber, first ensure that the machine has finished its programme and is empty. To gain access gently ease down the top of the plinth panel situated at the base of the machine, with a screwdriver etc, to release it. Place a shallow dish or tray below the cover of the pre-chamber to catch the small amount of water present. Re-fit the plinth cover by inserting the hooks on its lower edge into the slots and ease the top edge back into position. Fig. [. . . ]