User manual INDESIT KN6G21S(W)/FR

[. . . ] Le présent appareil peut être utilisé par des enfants de plus de 8 ans et par des personnes présentant des capacités physiques, sensorielles ou mentales réduites ou n'ayant pas l'expérience ou les connaissances nécessaires, à condition qu'ils soient sous bonne surveillance ou qu'ils aient reçu les instructions nécessaires pour une utilisation de l'appareil en toute sécurité et à condition qu'ils se rendent compte des dangers encourus. Pièces voisines (voir figure B) ­ à condition qu'il ne Using the hob Using the oven Oven cooking advice table precautions and tips , 22 General safety Disposal Respecting and conserving the environment maintenance and care , 23-24 Switching the appliance off Cleaning the appliance Gas tap maintenance Replacing the oven light bulb Assistance WARNING: The appliance and its GB accessible parts become hot during use. Children less than 8 years of age shall be kept away unless continuously supervised. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. [. . . ] Checking the tightness of the connection When the installation process is complete, check the hose fittings for leaks using a soapy solution. It is possible to adapt the appliance to a type of gas other than the default type (this is indicated on the rating label on the cover). Unscrew the nozzles using a 7 mm socket spanner (see figure), and replace them with nozzles suited to the new type of gas (see Burner and nozzle specifications table). Replace all the components by following the above instructions in reverse. Remove the knob and adjust the regulatory Screw, which is positioned inside or next to the tap Pin, until the flame is small but steady. Supply, the regulatory screw must be fastened as While the burner is alight, quickly change the position Of the knob from minimum to maximum and vice versa Several times, checking that the flame is not The hob burners do not require primary air adjustment. Unscrew the nozzle using a special nozzle socket spanner (see figure) or with a 7 mm socket spanner, and replace it with a new nozzle that is suited to the new type of gas (see Burner and nozzle specifications table). Turn the knob to the minimum position (MIN) after it has been in the maximum position (MAX) for approximately 10 minutes. Tighten or loosen the adjustment screws on the outside of the thermostat pin (see figure) until the flame is small but steady. In the case of natural gas, the adjustment screw must Turn the knob from the MAX position to the MIN position quickly or open and shut the oven door, making sure that the burner is not extinguished. Turn off all the burners and the electric plates before closing the lid. For each BURNER knob there is a complete ring showing the strength of the flame for the relevant burner. Press the BURNER knob and turn it in an anticlockwise direction so that it is pointing to the maximum flame setting . Adjust the intensity of the flame to the desired level by turning the BURNER knob in an anticlockwise direction. This may be the minimum setting , the maximum setting or any position in between the two. If the appliance is fitted with The BURNER knob and turn The burner may be extinguished when If this occurs, repeat the Operation, holding the knob down for a longer period If the flame is accidentally extinguished, switch off the burner and wait for at least 1 minute before attempting to relight it. If the appliance is equipped with a flame failure safety device* (X), press and hold the BURNER knob for approximately 2-3 seconds to keep the flame alight and to activate the device. To switch the burner off, turn the knob until it reaches the stop position · Practical advice on using the burners For the burners to work in the most efficient way possible and to save on the amount of gas consumed, it is recommended that only pans that have a lid and a flat base are used. To identify the type of burner, please refer to the diagrams contained in the "Burner and nozzle specifications". When inserting the Shelf make sure the This appliance has been designed and manufactured in compliance with international safety standards. The following warnings are provided for safety reasons and must be read carefully. These instructions are only valid for the countries whose symbols appear in the manual and on the serial number plate. [. . . ] It is usually sufficient simply to wash the hob using a damp sponge and dry it with absorbent kitchen roll. The stainless steel or enamel-coated external parts and the rubber seals may be cleaned using a sponge that has been soaked in lukewarm water and neutral soap. The hob grids, burner caps, flame spreader rings and the hob burners can be removed to make cleaning easier; wash them in hot water and non-abrasive detergent, making sure all burnt-on residue is removed before drying them thoroughly. For hobs with electronic ignition, the terminal part of the electronic lighting devices should be cleaned frequently and the gas outlet holes should be checked for blockages. [. . . ]