User manual INFOCUS LP1200 Reference Guide

[. . . ] USER'S GUIDE 1 ESPAÑOL ITALIANO DEUTSCH FRANÇAIS ENGLISH APPENDIX CAUTION ENGLISH RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. If you use another power-supply cord, it may cause interference with radio and television reception. Use the attached VGA cable, RS-232C cable with this equipment so as to keep interference within the limit of a Class A device. [. . . ] Select GAMMA CORRECTION of PICTURE menu and then press the ENTER button. (The GAMMA CORRECTION menu appears on-screen display. ) GAMMA CORRECTION - USER MASTER R G B 0 10 20 30 40 50 60 70 80 90 100 If you wish to change the color balance, follow the steps below. Press the or buttons on the control panel (or $ or % buttons on the remote control) to select MASTER, and then press the ª or º buttons on the control panel (or { or } buttons on the remote control) to select the desired color R, G or B. GAMMA CORRECTION - USER RESET Horizontal axis: Vertical axis: Inclination: brightness of the input signals brightness of the output signals GAMMA MASTER R G B 0 10 20 30 40 50 60 70 80 90 100 RESET or buttons on the control panel (or 2. Press the $ or % buttons on the remote control) to select MASTER. GAMMA CORRECTION - USER MASTER R G B 0 10 20 30 40 50 60 70 80 90 100 7. Press the or buttons on the control panel (or $ or % buttons on the remote control) to select the points brightness of the input signals. GAMMA CORRECTION - USER MASTER R RESET G B 0 10 20 30 40 50 60 70 80 90 100 RESET 3. Press the or buttons on the control panel (or $ or % buttons on the remote control) to select the points brightness of the input signals. GAMMA CORRECTION - USER MASTER R G B 0 10 20 30 40 50 60 70 80 90 100 8. Press the ª or º buttons on the control panel (or { or } buttons on the remote control) to adjust the brightness of the output signals. GAMMA CORRECTION - USER MASTER R RESET G B 0 10 20 30 40 50 60 70 80 90 100 4. Press the ª or º buttons on the control panel (or { or } buttons on the remote control) to adjust the brightness of the output signals. GAMMA CORRECTION - USER MASTER R G B 0 10 20 30 40 50 60 70 80 90 100 RESET 9. · To switch back to the default condition of GAMMA CORRECTION, select RESET and press the ENTER button when the GAMMA CORRECTION display appears. · When selecting RESET, the buttons cannot be operated for 2 to 18 seconds. RESET 5. Repeat steps 3 and 4 for another point setting. 24 Advanced feature for presentation Cursor operation 1. (The operation indicator will turn off if the remote control is not used for a period of five minutes. ) 3. Move the cursor by using the remote control. Move to left Move to right 2. Press the SELECT button until the desired form is appeared. . . . . . . . . . . . Press the START/STOP button to momentarily freeze the cursor movement. · When using the EXPAND mode, a red frame will not appear if the cursor is selected. Press the SELECT button until the desired width of the line is appeared. Press the SELECT button until the desired color of the line is appeared. Position the cursor where you want the path to begin and press the SELECT button. · The red frame will be disappeared by pressing the CANCEL button. Move the cursor to where you want the point of the opposite corner and press the SELECT button again. · By pressing the CANCEL button, the line or frame will disappear. [. . . ] When having a control sequence by RS232C, reject other codes by the personal computer side. [Example] Turn the power ON (' 'is for ASCII code) Sending commands from the PC etc. 30 30 21 0D '0' '0' '!' ' ' 30 30 21 0D '0' '0' '!' ' ' Command received (Command echo back) Status code from projector Command for POWER ON Meaning 4) Operation commands The operation commands execute the basic operation setting of this projector. It may not operate when changing the signal. POWER ON POWER OFF INPUT RGB1 INPUT RGB2 INPUT VIDEO1 INPUT VIDEO2 INPUT CARD1 INPUT CARD2 ASCII !" _r1 _r2 _v1 _v2 _c1 _c2 HEX 21h 22h 5Fh 5Fh 5Fh 5Fh 5Fh 5Fh 72h 72h 76h 76h 63h 63h 31h 32h 31h 32h 31h 32h [Example] Set the input signal to RGB1 (' 'is for ASCII code) Sending commands from the PC etc. [. . . ]