User manual INFOCUS SP4800 Reference Guide

[. . . ] User's Guide [ English · Français · Deutsch · Español · Italiano · Norsk ] ENGLISH Declaration of Conformity Manufacturer: InFocus Corporation, 27700B SW Parkway Ave. Wilsonville, Oregon 97070 USA European Office: Strawinskylaan 585, 1077 XX Amsterdam, The Netherlands We declare under our sole responsibility that the ScreenPlay 4800 projector conforms to the following directives and norms: EMC Directive 89/336/EEC, Amended by 93/68/EEC EMC: EN 55022 EN 55024 EN 61000-3-2 EN 61000-3-3 Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC Safety: EN 60950: 2000 June, 2003 Trademarks Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc. IBM is a trademark or registered trademark of International Business Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered trademarks of Microsoft Corporation. [. . . ] Please insure your shipment for its full value. Regarding this projector When sending your projector in for repair, we recommend shipping the unit in its original packing material, or having a professional packaging company pack the unit for shipping. Please insure your shipment for its full value. 26 Using the remote control The remote uses two (2) provided AAA batteries. They are easily installed by sliding the cover off the remote's back, aligning the + and - ends of the batteries, sliding them into place, and then replacing the cover. To operate, point the remote at the projection screen or at the projector (not at the video device or computer). Press the remote's Menu button to open the projector's menu system. Use the arrow buttons to navigate, and the Select button to select features and adjust values in the menus. The remote also has: · · · · · · · · · · · Power button to turn the projector on and off (see page 19 for shutdown info) backlight button to light the remote's buttons in the dark Brightness and Contrast buttons to adjust the image Blank button to display a blank screen instead of the current image (to change the color of the screen, see page 36) Source buttons to switch among sources (to assign a particular source to a source button, see page 35) and a source toggle Resize button to change the Aspect Ratio (see page 32) Auto Image button to resynch the projector to the source Preset button to restore stored settings (see page 33) Overscan button to remove noise in a video image (page 34) Make sure the batteries are installed in the proper orientation and are not dead. Make sure you're pointing the remote at the projector or the screen, not at the video device or the computer, and are within the remote range of 30 feet (9. 14m). backlight button navigation buttons Troubleshooting the remote 27 Using the audio To use the projector's speaker, connect your source to the Audio In connector on the projector. Troubleshooting Audio If you aren't hearing the audio, check the following: · · · · · Make sure the optional audio cable is connected. If playing a video, make sure the playback has not been paused. connect optional audio cable adjust volume Using the keypad buttons Most buttons are described in detail in other sections, but here is an overview of their functions: Menu­opens the on-screen menus (page 31). Up/Down arrows­navigates to and adjusts settings in the menus (page 31). Video and Computer­changes the active source. menu navigation buttons 28 Optimizing computer images After your computer is connected properly and the computer's image is on the screen, you can optimize the image using the onscreen menus. · · · · · Adjust the Keystone, Contrast, or Brightness in the Picture menu (page 32). Adjust the phase, Tracking, or Horizontal or Vertical position in the Advanced menu (page 34). Once you have optimized the image for a particular source, you can save the settings using Presets. This allows you to quickly recall these settings later (page 33). Presentation features Several features are provided to make giving presentations easier. · The Blank button on the remote allows you to display a blank screen instead of the active source. The Startup Logo option lets you change the default start up screen to a blank or default screen (page 36). Power Save is provided to automatically shut down the projector after several minutes of inactivity. This helps preserve lamp life (page 35). · · 29 Optimizing video images After your video device is connected properly and the image is on the screen, you can optimize the image using the onscreen menus. · · · · · · Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture menu (page 32). Turn on Overscan to remove noise on the edges of the image. Customizing the projector You can customize the projector for your specific setup and needs. [. . . ] DISCLAIMER OF UNSTATED WARRANTIES THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE ARE DISCLAIMED. THERE ARE NO WARRANTIES THAT EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF AND THE FOREGOING WARRANTY SHALL NOT BE EXTENDED, ALTERED OR VARIED EXCEPT BY WRITTEN INSTRUMENT SIGNED BY INFOCUS. SOME JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY MAY LAST, SO SUCH LIMITATIONS MAY NOT APPLY TO YOU. · WARRANTY LIMITATION AND EXCLUSION THIS WARRANTY SETS FORTH INFOCUS' MAXIMUM LIABILITY FOR ITS PRODUCT. [. . . ]