User manual INSINKERATOR FILTER SYSTEM

[. . . ] The filter system is equipped with a vent line that opens when the filter cartridge is removed. Under normal conditions, approximately 2 ounces (~60 cc) of water is discharged from the vent. To conveniently redirect this discharge, a 6" section of gray tubing is provided. [. . . ] To connect one plumbing fixture: Completely insert the plumbing fixture's 1/4" copper tubing into one of the outlets of the "Y" fitting. In the other outlet of the "Y" fitting, insert the provided plug. To connect two plumbing fixtures: Completely insert both plumbing fixture's 1/4" copper tubes into both outlets of the "Y" fitting. To remove a tube from its quick-connect fitting, depress the release ring into the fitting and gently pull the tube away from the fitting. 4. Connect to Cold Water Supply Line Supplied with the unit is a brass nut, ferrule and tube insert to connect the polyethylene tube from the input side of the filter to a standard 3/8" compression fitting. Other plumbing connections are possible ­ check with a qualified plumber should you have questions. Slide the nut and ferrule over the tube and then push in the tube insert. Insert the tube into a standard 3/8" compression fitting (not supplied) and tighten. Test the Water Connection Test the water connection to see if it is watertight. If it is not, relieve water pressure by turning off the water supply, and adjust or tighten fittings as necessary. F201 Chemical & Mechanical Reduction Filter Specifications: (Use replacement cartridge F-201R) This cartridge (included with the system) provides mechanical and chemical reduction of dirt/rust, taste/odor, chlorine and particulates. System is tested and certified by NSF International against ANSI/NSF Standard 42 for the reduction of Particulate Class I, Chlorine Class I, Taste and Odor. Pressure: 30-125 psi Temperature: 33°F­100°F Flow Rate: 0. 75 gpm Capacity: 500 gallons Filter Capacity: 500 gallons, depending on local water conditions. Note that while the testing was performed under standard laboratory conditions, actual performance may vary. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems must be installed and operated in accordance with the Manufacturer's recommended procedures and guidelines. For service and parts, contact your local dealer or In-Sink-Erator directly at 1-800-558-5700. Contaminant Reduction Taste/Odor/ Chlorine Particulates Average Influent ppm 2. 10 286667 Product Water ppm 0. 05 1683 Average Reduction 97% 99% USEPA Recommendation N/A N/A NSF Test 500180-00 500181-00 Application guidelines/Water Supply Parameters for NSF Testing: Service flow of 0. 75 gpm, community or private well water supply, water pressure of 30-125 psi, water temperature of 33°F­100°F . Except as noted, all testing performed at pH = 7. 5±0. 5, Flow: 0. 75 gpm, Pressure: 60 psi, Temp:20°±3°C. Contact an authorized In-Sink-Erator service agent for repairs or replacement components. Warranty Information Full 1 Year Warranty: Covers all replacement parts and repair labor to correct defects in material or workmanship in the filter system, excluding the replaceable filter cartridge, for the full warranty period from the date of installation in your home. If warranty service is required during the warranty period, contact an authorized In-Sink-Erator service agent to replace or repair the unit in your home at no cost to you. This warranty gives you specific legal rights and you may also have other rights which vary. [. . . ] Toutes les autres marques déposées sont la propriété de leurs entreprises respectives. ©2002 In-Sink-Erator In-Sink-Erator® es una marca comercial registrada de InSink-Erator, una división de Emerson Electric Co. El resto de las marcas comerciales son propiedad de sus respectivas compañías. [. . . ]