User manual JUNO JGU2423

[. . . ] Before any cleaning or maintenance work is carried out, be sure to switch off and unplug the appliance. If the appliance is transported horizontally, it is possible that the oil contained in the compressor flows in the refrigerant circuit. It is advisable to wait at least two hours before connecting the appliance to allow the oil to flow back in the compressor. The inner lining of the appliance consists of channels through which the refrigerant passes. [. . . ] This appliance does not contain gasses which could damage the ozone layer, in either its refrigerant circuit or insulation materials. The appliance shall not be discarded together with the urban refuse and rubbish. Avoid damaging the cooling unit, especially at the rear near the heat exchanger. Information on your local disposal sites may be obtained from your municipal authorities. Take utmost care when handling your appliance so as not to cause any damages to the cooling unit with consequent possible fluid leakages. There must be adequate ventilation round the back of the appliance and any damage to the refrigerant circuit must be avoided. For freezers only (except built-in models): an ideal location is the cellar or basement. 12 INSTALLATION If this appliance featuring magnetic door seals is to replace an older appliance having a spring lock (latch) on the door or lid, be sure to make that spring lock unusable before you discard the old appliance. Do not use detergents or abrasive powders, as these will damage the finish. Location Fig. 1 Positioning The appliance should be installed well away from sources of heat such as radiators, boilers, direct sunlight etc. ; best performance is obtained with ambient temperature between +18°C and +43°C (class T); +18°C and +38°C (class ST); +16°C and +32°C (class N); +10°C and +32°C (class SN). For building into kitchen units follow the special "Building-in" instructions given. Attention: keep ventilation openings clear of obstruction. 450 547 550 This appliance is designed to be built-in to a space having the dimensions given in Fig. 8). D533 2 Insert the securing screws (C) through elongated holes (2) and fix the panel without tightening the screws (Fig. 9 Keeping the appliance central in the recess, slide it in until its back touches the wall. With a tape measure (or similar instrument), measure distance (A) between the top edge of the door and the top edge of the decorative panel, placing it next to the recess. Once the top of the panel has been correctly positioned, fix it through the holes in the bottom bracket, without tightening the screws (Fig. 10 Check the position again by slackening the screws and pins then, once the best position has been obtained, fully tighten all the fixings. Cover the visible part of the top bracket on the panel with plastic D472 cover (D), inserting it in the locations provided in the bracket. D Fig. 11 Once the door has been correctly aligned, tighten the holding nuts on the fixing brackets and attach the appliance to the adjacent units and the bottom of the work surface (Fig. 50cm2 450 D690 For a correct installation operation if the base plate is more than 100 mm (for cavity height 820 mm) or more than 150 mm (for cavity height 870 mm) you must cut out the plate as shown in Fig. 12. 15 USE The freezer is marked with the for long-term storage of frozen food. symbol, which means that the compartment is suitable for freezing food and Control panel A 0 56 C D 12 A - ON/OFF switch and operating pilot light B - Temperature adjustment knob Operation Insert the plug into the wall socket. Move the ON/OFF switch (A) to the ON position; it will light up to indicate that the appliance is switched on. Turn the thermostat knob, clockwise, beyond the «O» (STOP) position. [. . . ] Small pieces may even be cooked still frozen, directly from the freezer: in this case, cooking will take longer. Ice-cube production This appliance is equipped with one or more trays for the production of ice-cubes. Fill these trays with water, then put them in the freezer compartment. Do not use metallic instruments to remove the trays from the freezer. 17 Defrosting In the freezer, frost should be removed with the special plastic scraper provided, whenever the thickness of the frost exceeds 4 mm. During this operation it is not necessary to switch off the power supply or to remove the foodstuffs. [. . . ]