User manual JUNO JKG7494

[. . . ] The domestic refrigerators and freezers are designed to be used specifically for the storage of edible foodstuffs only. Manufacturers' storage recommendations should be strictly adhered to. During normal operation, the condenser and compressor at the back of the appliance heat up considerably. For safety reasons, minimum ventilation must be as shown in the relevant Figure. [. . . ] This appliance complies with EEC directive number 87/308 of 2/6/87 relative to radio interference suppression. Directives: - 73/23 EEC of 19. 2. 73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3. 5. 89 (Electromagnetic Compatibility Directive) and subsequent modifications. Positioning The appliance should be installed well away from sources of heat such as radiators, boilers, direct sunlight etc. ; best performance is obtained with ambient temperature between +18°C and +43°C (class T); +18°C and +38°C (class ST); +16°C and +32°C (class N); +10°C and +32°C (class SN). For building into kitchen units follow the special "Building-in" instructions given. Cleaning the interior Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly. Do not use detergents or abrasive powders, as these will damage the finish. 15 Door reversibility (Fig. 1 Right opening Remove the pins (P) and (P1). Left opening Remove (P) from both sides and the door. Remove (P1) from the right side. 16 Building-in instructions Housing dimensions Height Depth Width 1780 mm 550 mm 560 mm Open the door and push the appliance against the side of kitchen furniture opposite to that of appliance hinges. Fasten the appliance with 4 screws provided in the kit included with the appliance. 2: Attention: keep ventilation openings clear of obstruction. 50 mm min. cm 200 2 C Press in the joint covers between the appliance and the kitchen furniture. D369 Fig. 6 D526 Push appliance into housing until stop strip (A) touches the kitchen unit. Fig. 3 A D098 Apply covers (B) on joint cover lugs and into hinge holes. Fig. 7 D023 If after having carried out the operation described in section 3 there is still some space left between the appliance and the kitchen unit, fit the trimming provided together with the appliance on the stop strip (A). Fig. 4 B A D096 D265 17 Position the runners (H) at the top and bottom of the inside of the kitchen unit as shown in Fig. After preparing the holes, screw the runners to the kitchen unit door using 3. 5x16 mm screws. Fig. 8 In case of side fixing of the appliance, it will be sufficient to loose the screws fixing the bracket (G) and to position it as shown in Fig. 11 H G 20m m D397 G D094 Open both the appliance door and that of the kitchen unit to approx. Hold the doors of the appliance and the unit together and mark the holes. Fig. 9 8mm PR34 Remove the little plates and make the holes with a diam. Replace the little plates over the runners and screw in the screws provided (3. 5x16 mm). For the alignment of the kitchen unit door, if necessary, use the clearance size of the slotted holes. At the end of the procedure, check that the doors of the appliance and the kitchen unit open properly. Fig. Pilot light Use of the freezer Operation Insert the plug into the wall socket. [. . . ] Introduce the plastic scraper in the appropriate seating as shown in Figure 17, place underneath a basin to collect the defrost water. 17 Do not use metallic instruments to remove the trays from the freezer. D068 Keep the scraper for future use. 22 MAINTENANCE Unplug the appliance before carrying out any maintenance operation. Warning This appliance contains hydrocarbons in its cooling unit; maintenance and recharging must therefore only be carried out by authorized technicians. Interior light The light bulb inside the refrigerator compartment can be reached as follows: unscrew the light cover securing screws; unhook the moving part by pressing it as shown in the figure. If the door is open and the light does not come on, check that the bulb is properly screwed in; if it still does not work, replace the bulb with one of the same power. [. . . ]