User manual KENWOOD C-V751

[. . . ] AV CONTROL CENTER C-V751 INSTRUCTION MANUAL KENWOOD CORPORATION B60-4341-10 01 CH (T, X) AP 9904 Before applying power Units are designed for operation as follows. Caution : Read this page carefully toBefore applying power ensure safe operation. 2 Europe and U. K. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 230 V only Australia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 240 V only For the United Kingdom Factory fitted moulded mains plug 1. [. . . ] ÷ When DVD 6ch INPUT is selected, all the speaker levels become 0 dB so the levels should be set on the source component. Regarding TAPE 2/MONITOR A cassette deck or graphic equalizer can be connected to this unit's TAPE 2/MONITOR terminals. If you connect a 3-head cassette deck, you can monitor the source sound, or the sound being recorded, while recording. Pressing the TAPE 2/MONITOR key lets you compare the recorded sound and the source sound. Refer to the operating manual for the component you connected for further details. Sound adjustment Sound adjustment 29 Ajustment for surround play (while listening to music) (SOUND) 1 Adjusting the tone (Stereo status only) GRC 1 Enter the SOUND adjustment mode. (Select the icon) Main unit Each press of the SOUND key switches the indication. 1 2 3 4 5 6 BASS TREBLE C LS/RS SW MIDNIGHT : : : : : Tone, Bass Tone, Treble Center speaker Surround speaker, Left/Right Sub woofer so un d 2 Select the "Tone" icon. (Select the icon) ÷ Adjustments 1 and 2 are not available in other modes than STEREO and "Tone" is set to "On". ÷ Adjustments 3, 4 and 5 are available only when the corresponding speakers are set. · ÷ With the GRC, the adjustment items shown in a single menu can be adjusted at once. (The adjustment steps 1, 2 are provided in a single menu so they can be adjusted successively without changing the menu screen. ) ÷ 6 is available only with the Digital input. To decrease To increase Note 3 Touch to turn the tone setting on or off. This adjustment is possible only when the PCM or Analog input is used and the listen mode is set to STEREO. or right arrow 4 Touch the left next to a tone setting (treble or bass) to between the adjust it. A readout arrows shows the current setting. The display on the GRC disappears if no operation on the GRC has been pressed for about 7 seconds. Bass tone level FM AM MW LW BAss _2 AUTO SOUND DIG DTS DOLBY DIG PRO LOGIC D MHz SLEEP KHz TIMER 1 2 TA ÷ The level can be adjusted between -10 and +10 in step of 2. Treble tone level EREO UNED F M TP A M NEWS MW LIP LW ÷ The level can be adjusted between -10 and +10 in step of 2. TREB +2 AUTO SOUND DTS DOLBY PRO LOGIC MHz SLEEP KHz TIMER 1 2 2 Adjust the volume levels for the speakers. (In other modes than stereo) 1 Select the "SP Level" icon. (Select the icon) ÷ This adjustment is not available when DVD 6ch INPUT is selected. To increase To decrease Continued to next page Sound adjustment 30 2 Adjust the center speaker level. "C" (Select the icon) TEREO TUNED F M N TP A M NEWS MW CLIP LW Main unit center speaker level Cch +2 AUTO SOUND DTS DOLBY PRO LOGIC MHz SLEEP KHz TIMER 1 2 3 Adjust to the desired level by pressing keys and 4 Adjust the surround speaker level. "LS/ RS" (Select the icon) ÷ The level can be adjusted between -10 and +10 in step of 1. Surround speaker level TEREO TUNED F M N TP A M NEWS MW CLIP LW or s +1/ +1 AUTO SOUND D DTS DOLBY D PRO LOGIC MHz SLEEP KHz TIMER 1 2 T 5 Adjust to the desired level by pressing keys and ÷ The level can be adjusted between -10 and +10 in step of 1. 6 Adjust the subwoofer level. "SW" (Select the icon) TEREO TUNED F M N TP A M NEWS MW CLIP LW Sub woofer level sW + 1) AUTO SOUND DTS DOLBY PRO LOGIC MHz SLEEP KHz TIMER 1 2 ÷ The level can be adjusted between -10 and +10 in steps of 1. 7 Adjust to the desired level by pressing and keys ÷ The volume levels adjusted here are just temporary; they return to the levels originally set in the setup operation when the power is turned off, the input selector is switched or the setup operation is started. MIDNIGHT function 1 Select the "Midnight" icon. MIDNIGHT function Any time you don't want to experience the loud and soft volume extremes of recorded sound (for example, late at night), use MIDNIGHT function to reduce volume extremes. This feature keeps loud, dramatic sound from being too loud (perhaps disturbing family members or neighbors) while ensuring that you can still hear whispered dialog or other soft sounds. Midnight function only works if you are listening to a Dolby Digital program that has been encorded with special compression data. 2 Select the MIDNIGHT mode. Each press changes the mode. For quietest balancing (the least difference between the loudest and quietest sound). 3 OFF Recording When recording sound with a recorder component of KENWOOD, synchro recording is possible by setting the INPUT SELECTOR to select MD or TAPE 1 according to the connected component. Sound may not be reproduced when the input signal and LISTEN MODE are selected improperly. How to select the digital input, analog input and LISTEN E MODE. Recording 31 Recording an analog input source 1 To record a music source Main unit GRC 1 Select the "edit" icon in the fixed segment screen. [. . . ] ± 10 dB (at 100 Hz) TREBLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 10 dB (at 10 kHz) Output level / impedance TAPE REC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 mV / 1 k 63 AM Tuner section (for Australia) Tuning frequency range . . . . . . . . . . . . . . . . . . . . . . . . . 531 kHz ~ 1, 602 kHz Usable sensitivity (30% mod. , S/N 20 dB) . . . . . . . . . . . . . . . . . . . . . [. . . ]