User manual KENWOOD HM-332

[. . . ] MICRO HI-FI COMPONENT SYSTEM HM-332 INSTRUCTION MANUAL KENWOOD CORPORATION COMPACT DIGITAL AUDIO TEXT B60-4726-08 (EN) 2 Before applying power Units are designed for operation as follows. Caution : Read this page carefully to ensure safe operation. Europe and U. K. AC 230 V only China and Russia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 120 V only Australia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 240 V only For the United Kingdom Factory fitted moulded mains plug 1. [. . . ] 1 "FM 50 kHz" (FM 50 kHz, AM 9 kHz) 2 "FM 100 kHz" (FM 100 kHz, AM 10 kHz) Area 1 USA, Canada and South American countries 2 Other countries CHANNEL Space Frequency FM: 100 kHz AM: 10 kHz FM: 50 kHz AM: 9 kHz Blinks. 5 Establish the selection by pressing the set/ demo key. Basic section 23 24 Recording on tape Stop the recording 1 5 4 Pause the recording 3 3 2 Stop the recording Basic section 1. 3 Press the TAPE 0 key. TAPE 0 1 ÷ Differentiation between normal (TYPE ) and high (TYPE automatically. Select the tape transport direction. To reverse the transport direction TAPE 2 3 1 Press the TAPE23 key corresonding to the desired direction. 2 Stop playback. ÷ When recording is started, the tape is transported in the direction selected in this step. 2 Check the tape transport direction indicator. ÷ Wind the tape to the position where recording is to be started. * Recording on tape 25 menu 3. Set the recording condition. up volume/ multi control Select the reverse mode. ( ÷ The tape equalizer is defeated during recording. down set/demo 3 Select an input source other than "TAPE" Example: To select the CD input CD 4. Select the source to be recorded. CD TUNER (Broadcasts) AUX (External input) "Adjusting the AUX input level" 01 CD 0:00 6 The character information display shows the recording input source. 4 TAPE rec ÷ If a CD has already been loaded, it starts to play now. Start recording. 5 Pause the recording TAPE rec 1 Press the TAPE rec key. 2 Play (or tune) the input source to be recorded. ÷ Recording stops automatically when the tape side(s) to be recorded have been fully recorded. Points in CD recording Blinks TAPE REC When recording CD tracks onto a tape, if you leave the cassette deck in record-pause mode beforehand, the cassette deck recording can be started at the CD starts to be played. ÷ Press the TAPE rec key during recording. (Press the key again to resume recording. ) Stop the recording STOP 7 1 Put the CD player in pause mode. (The CD player pauses at the beginning of the selected track. ) 3 Put the cassette deck in Record-pause mode. (Recording starts) ÷ To stop recording, press the 7STOP key. Note Note that this cassette deck cannot record onto Metal tapes. Do not use a cassette with more than 90-minute recording time, for the tape used with such a cassette is very thin and tends to cause troubles such as entanglement around the pinch roller or cutting of tape. 26 Various CD playback features Use the following procedure to program desired tracks in a desired order. (up to 32 tracks) Listening in the desired sequence (program playback) Select the CD input. 1 Let the "PGM" indicator light. Press in stop mode PGM AUTO/MONO Lights PGM -P-01 C D KENWOOD Selection of tracks PGM Select 2 want totrack numbers in the order you play them. 1 Select the track. Program position of the track to be selected next. 05 P-01 Press the numeric keys as shown below. . . . 40 : 0000) 2 Confirm the selection. SET ( To select more than one track, repeat steps 1 and 2 for each track. ) ÷ A track can also be selected using the 4 or ¢ key. When "PROGRAM FULL" is displayed, no more tracks can be programmed. ÷ If you made a mistake, press the CLEAR key and enter the track No. is entered, the track will be added to the end of the existing program. ÷ "­ ­ : ­ ­" is displayed when the total programmed period has attained 100 minutes or more. 3 Start playback. Application section CD / ÷ Tracks will be played in the order they were programmed (following the program numbers). ÷ When the 4 or ¢ key is pressed during play, the program will jump to the preceding or the following track respectively. ÷ When the 4 key is pressed once during playback, the play position returns to the beginning of the current track being played. To stop playback To quit the program mode Clearing tracks from the end Press in stop mode STOP CLEAR Clearing the program Press in stop mode PGM AUTO/MONO -- P-05 CLEAR ÷ The entire program is cleared. (P-5 has been deleted. ) ÷ Each time the key is pressed, the last track in the program is cleared. Various CD playback features 27 Repeated playback You can repeatedly listen to a favorite track or disc. Select the CD input. Setup for repeating a single track 1 Confirm that the "PGM" indicator is not lit. PGM ÷ If the "PGM" indicator is lit, press the PGM/AUTO/ MONO key to turn it off. Confirm that this is not lit. PGM AUTO/MONO 01 0:00 2 Play the track to be repeated. CD / 3 Select "REPEAT". REPEAT Each press switches the repeat mode. Lights REPEAT Setup for repeating all tracks in a disc 1 Confirm that the "PGM" indicator is not lit. PGM 01 0:12 C D KENWOOD ÷ If the "PGM" indicator is lit, press the PGM/AUTO/ MONO key to turn it off. Confirm that this is not lit. PGM Application section AUTO/MONO 2 Select "REPEAT ALL". REPEAT 01 CD 0:00 Each press switches the repeat mode. [. . . ] and Europe) Effective output power during STEREO operation 1 kHz, 10 % T. H. D. , at 6 . . . . . . . . . . . . . . . . . . . 20 W + 20 W Rated output power during STEREO operation 1 kHz, 0. 7 % T. H. D. , at 6 . . . . . . . . . . . . . . . . . . . . . . . and Canada) Rated output power during STEREO operation 14 watts per channel minimum RMS, both channels driven, at 6 from 90 Hz to 20 kHz with no more than 0. 9 % total harmonic distortion. (FTC) (For other countries) Rated output power during STEREO operation 1 kHz, 10 % T. H. D. , at 6 . . . . . . . . . . . . . . . . . . . [. . . ]