User manual KENWOOD HM-535

[. . . ] MICRO HI-FI COMPONENT SYSTEM HM-535 INSTRUCTION MANUAL KENWOOD CORPORATION COMPACT DIGITAL AUDIO B60-5240-10 02 MA (K, T, M, X, E2) FE 0201 Before applying power Caution : Read this page carefully to ensure safe operation. Units are designed for operation as follows. AC 120 V only Australia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 230 V only Before applying power China and Russia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 110-120 / 220-240 V switchable* For the United Kingdom * AC voltage selection The AC voltage selector switches on the rear panel are set to the voltage that prevails in the area to which the unit is shipped. [. . . ] In this case, change the channel space setting in accordance with your area by referring to the following table. Main unit only 1 Turn power on. 2 While holding TUNER/band key pressed, turn the volume knob to select "FM 50 k" or "FM 100 k". Each press switches the space frequency alternately. 1 FM 50 k 2 FM 100 k ÷ At FM 50 kHz, the corresponding AM frequency is 9 kHz. At FM 100 kHz, the corresponding AM frequency is 10 kHz. 3 Set it. 1 2 Area USA, Canada and South American countries Other countries CHANNEL Space Frequency FM: 100 kHz AM: 10 kHz FM: 50 kHz AM: 9 kHz 21 EN Receiving Playback of TAPE broadcast station Tuning to a non-preset radio station (Auto tuning, Manual tuning) Select the tuning mode according to the radio wave receiving condition. When the receiving condition is good: AUTO mode When it is poor due to weak radio waves: MANUAL mode ÷ In MANUAL mode, FM stations are received in monaural. 1 Select the AUTO or MANUAL mode. Each press alternates the mode. 1 "AUTO" : Stereo reception ("AUTO" lit) 2 "MANUAL" : Monaural reception ("AUTO" not lit) ÷ Normally, use the AUTO (Auto tuning, stereo reception) mode. AUTO/MONO STOP 7 In AUTO mode : 2 Tune a station. To decrease frequency 1 TUNING 1 The next preset station can be received automatically every time the TUNING (1 or ¡) key is pressed. To increase frequency In MANUAL mode : Press the TUNING (1 or ¡) key repeatedly until the desired station is received. The desired station can also be received by holding the TUNING (1 or ¡) key depressed until its frequency is displayed. One-by-one presetting (Manual preset) Remote control unit only 1 Perform the procedure in "Tuning to a nonpreset radio station (Auto tuning, Manual tuning)" to receive the station to be preset. 2 Press the ENTER key during reception. ENTER "MEMORY" lights (for approx. 20 sec. ) ÷ A maximum of 30 stations of the band presently being received will be preset. (Proceed to step 3 while "MEMORY" is lit. ) 3 Select one of the preset numbers from 1 to 30. 4 P. CALL 4 1 4 7 10 2 5 8 0 3 6 9 4 Press the ENTER key again. ENTER ÷ If several stations are preset under the same number, the previous memory is replaced with the latest memory contents. (Repeat steps 1, 2, 3 and 4 to preset other stations) 22 EN RDS (Radio Data System) (For U. K. and Europe) Playback of TAPE RDS is a system which transmits useful information (digital data) for FM broadcasts together with the broadcast signal. Tuners and receivers designed for RDS reception can extract the information from the broadcast signal for use with various functions such as automatic display of the station name. This unit is equipped with the following functions utilizing RDS data : PTY (Program Type Identification) Search :¢ The tuner automatically searches for a station which is currently broadcasting a specified program type (genre). The "RDS" indicator lights up when an RDS broadcast (signal) is received. PS (Program Service Name) Display : When an RDS broadcast is received, the station name is automatically displayed. ÷ Some functions may not be provided or be given different names depending on countries or areas. Before using RDS For reception of RDS stations, the auto memory function must be used to preset the stations. During the auto memory function, the presetting sequence priority will be given to the RDS stations. 23 EN RDS (Radio Data System) Playback of TAPE Searching for a desired program type (PTY search) By specifying the type of program (genre) you want to listen to, the tuner automatically searches for a station which is currently broadcasting a program of the specified type. However, if a station is not preset by auto memory, "NO DATA" will flash instead of the program (genre) type and PTY search is not available. Set the reception band to FM. ¡ 1 Select the PTY search mode. Remote control unit only ÷PTY ÷ TIME DISPLAY When an RDS broadcast is received, the program type is shown on the display. If no PTY data is available, or if the station is not an RDS station, "NONE" is displayed. 2 Select the desired program type. Use program type table on the right for your convenience. Program type table 4, ¢ keys Program Type Name Pop Music Rock Music Easy Listening Music Light Classical Serious Classical Other Music News Current Affairs Information Sport Education Drama Culture Science Varied Weather Finance Children's programs Social Affairs Religion Phone In Travel Leisure Jazz Music Country Music National Music Oldies Music Folk Music Documentary Display POP M ROCK M EASY M LIGHT M CLASSICS OTHER M NEWS AFFAIRS INFO SPORT EDUCATE DRAMA CULTURE SCIENCE VARIED WEATHER FINANCE CHILDREN SOCIAL RELIGION PHONE IN TRAVEL LEISURE JAZZ COUNTRY NATION M OLDIES FOLK M DOCUMENT Selection with the 4 or ¢ key. 4 DOWN 4 P. CALL 4 UP ¢ Select while "PTY" is lit. The desired program type can be selected with the 4 or ¢ key from 29 types. Press the key and release it when the desired type is displayed. 24 EN RDS (Radio Data System) Playback of TAPE 3 Start the search. ÷PTY ÷ When searching for a Rock Music broadcast Display while the tuner is searching. TIME DISPLAY Program type name display. ÷ If a program of the desired type cannot be found, "NO PROG" is displayed, then after several seconds the display returns to the original display. ÷ If a program of the desired type is found, that program is received and the program type name display changes to the station name display. Goes off To change to a different program type : Repeat steps 1, 2, 3. Station name display. 25 EN Recording on TAPE Recording on TAPE The tape deck of the unit can record signals only on Normal (Type ) tapes. It cannot record on High (Type ) and Metal (Type ) tapes. Stop the recording Stop the recording Start recording/ Pause the recording 1. [. . . ] Exit from the random play mode. For the U. S. A. Note to CATV system installer This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. 47 EN Specifications Main unit [Amplifier section] (For U. S. A. and Canada) Rated output power during STEREO operation (FTC) 43 watts per channel minimum RMS, both channels driven, at 6 from 90 Hz to 15 kHz with no more than 10 % total harmonic distortion. and Europe) Effective output power during STEREO operation (1 kHz, 10% T. H. D. , at 6 ) . . . . . . . . . . . . . . . . . 50 W + 50 W Rated output power during STEREO operation (1 kHz, 0. 7% T. H. D. , at 6 ) . . . . . . . . . . . . . . . . [. . . ]