User manual KENWOOD KDV-MP7032

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual KENWOOD KDV-MP7032. We hope that this KENWOOD KDV-MP7032 user guide will be useful to you.


KENWOOD KDV-MP7032 : Download the complete user guide (328 Ko)

Manual abstract: user guide KENWOOD KDV-MP7032

Detailed instructions for use are in the User's Guide.

[. . . ] € Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. € If your car’s ignition does not have an ACC position, connect the ignition wires to a power source that can be turned on and off with the ignition key. [. . . ] Fit the unit into the mounting sleeve by using four corners of the trim plate. Parts list for installation and connection The following parts are provided for this unit. 18 5:43:38 PM INSTALLATION (IN-DASH MOUNTING) The following illustration shows a typical installation. If you have any questions or require information regarding installation kits, consult your Kenwood car audio dealer or a company supplying kits. € If you are not sure how to install this unit correctly, have it installed by a qualified technician. € Make sure not to block the fan on the rear panel to maintain proper ventilation when installed. *1 When you stand the unit, be careful not to damage the fuse on the rear. 1 * Al poner la unidad vertical , tenga cuidado de no dañar el fusible provisto en la parte posterior. Fixador (opcional) Flat type screws—M5 x 8 mm (M5 x 3/8") *2 Tornillos tipo plano—M5 x 8 mm (M5 x 3/8 pulgada) *2 Protector Dashboard Tablero de instrumentos Parafusos de cabeça chata—M5 x 8 mm (M5 x 3/8 polegada) *2 Tablier Screw (option) Tornillo (opción) *2 Not included for this unit. Parafuso (opcional) Bracket *2 Ménsula *2 Support *2 Pocket Compartimiento Flat type screws—M5 x 8 mm (M5 x 3/8") *2 Tornillos tipo plano—M5 x 8 mm (M5 x 3/8 pulgada) *2 Parafusos de cabeça chata— M5 x 8 mm (M5 x 3/8 polegada) *2 Bracket *2 Ménsula *2 Suporte *2 Entrada Note: Install the unit at an angle of less than 30˚. When installing the unit on the mounting bracket, make sure to use the 8 mm (3/8")-long screws. Removing the unit Before removing the unit, release the rear section. Insert the two handles, then pull them as illustrated so that the unit can be removed. 18 5:43:40 PM ELECTRICAL CONNECTIONS To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all electrical connections before installing the unit. € Be sure to ground this unit to the car’s chassis again after installation. € It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 Ω to 8 Ω). [. . . ] € For amplifier only: – Disconnect the speakers from this unit, connect them to the amplifier. € You can switch off the built-in amplifier and send the audio signals only to the external amplifier(s) to get clear sounds and to prevent internal heat built-up inside the unit. are the “–” terminals of L and R speakers grounded in common? [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE KENWOOD KDV-MP7032




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual KENWOOD KDV-MP7032 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.