User manual KENWOOD KRC-152LA

[. . . ] · Do not set the removed faceplate or the faceplate case in areas exposed to direct sunlight, excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. · Do not subject the faceplate to excessive shock, as it is a piece of precision equipment. · To prevent deterioration, do not touch the terminals of the unit or faceplate with your fingers. [. . . ] The MONO indicator lights up when monaural reception is on. Auto Memory Entry You can automatically store all the receivable frequencies in the band currently being listened to, and then recall them with the touch of a button later. This function is especially useful when you are travelling and do not know what stations are available. Up to 6 frequencies can be stored this way. Station Preset Memory Store the frequency of the station currently being listened to. You can then recall that station with a single touch of a button. 1 Select the band for auto memory entry. 2 Hold down the AME button for two seconds or more to start auto memory entry. When all the stations in a certain band are stored in the preset memory, the auto memory entry stops. Recalling a Preset Station: Press the preset station button (#1-6) for the desired station. The number of the recalled station is displayed. NOTE 1 Select the band/ station that you want to have stored. 2 Hold down the button (#1-6) that you want to use for the station, for two seconds or more. The button number blinks once in the display to indicate that the data has been stored. Recalling a Preset Station: Press the preset station button (#1-6) for the desired station. The number of the recalled station is displayed. NOTE When the local seek function is turned whilst auto memory entry takes place, the auto memory entry function is cancelled. You can store 6 stations in each of the FM1, FM2, FM3, and AM (MW and LW) bands. --8-- Cassette player features (See page 5) Playing Cassette Tapes Loading and Playing Cassettes: Load a cassette with the tape exposed on the right. With Side A facing up, the 3 indicator lights up when Side A is playing, and 2 when Side B is playing. Playing Cassettes Already Loaded: Press the SRC button repeatedly until the tape mode is obtained. Listening to the other side: Press the FF button and REW button at the same time. Use the following table as a guide for adjusting the settings in each mode. Front channel increased. Adjustment mode (Display) Bass ("BAS") Treble ("TRE") Balance ("BAL") Fader ("FAD") 4 Press the MENU button to end the Time Adjustment mode. -- 10 -- Accessories Other features (See page 6) Theft Deterrent Faceplate The faceplate of the unit can be detached and taken with you, helping to deter theft. External view Number of items 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Projections Release button Grooves 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 3 Removing Faceplate: Press the release button. The faceplate is unlocked, allowing you to detach it. NOTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 4 2CAUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 · The faceplate is a precision piece of equipment and can be damaged by shocks or jolts. For that reason, keep the faceplate in its special storage case whilst detached. The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above. · Do not expose the faceplate or its storage case to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. Reattaching Faceplate: 1 Align the projections on the unit with the grooves on the faceplate. 2 Push the faceplate in until it clicks. The faceplate is locked in place, allowing you to use the unit. -- 11 -- Installation Procedure 1. [. . . ] Connect the cable correctly, referring to the section on "Connecting Cables to Terminals". No sound can be heard, or the volume is low. The Attenuator function is turned on. The cassette tape is not loaded properly. Nothing happens when the buttons are pressed. The sound quality is poor or distorted. The computer chip in the unit is not functioning normally. The speakers are not wired correctly. Radio reception is poor. The car antenna is not extended. [. . . ]