User manual KENWOOD KTC-1000R

[. . . ] · To prevent short circuits when replacing a fuse, first disconnect the wiring harness. · During installation, do not use any screws except for the ones provided. · When drilling a hole in the car to fix the brackets, make sure not to damage the fuel tank, brake tube, wiring harnesses, etc. [. . . ] · Insulate unconnected cables with vinyl tape or other similar material. · During use, the surface temperature of this unit will become high, therefore it should not be mounted where anything sensitive to the heat, such as people or resins, would come into contact with it. · Install this unit in a location which allows heat to easily dissipate. · Install the unit securely in a location that does not interfere with driving. English 3 Installation s Connecting Cables to Terminals 2WARNING If you connect the ignition cable (red) and the battery cable (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those cables to the power source running through the fuse box. Front left output (White) PREOUT REAR/NON-FAD FRONT NOTE Do not put anything into the fuse holder. TO 5L I/F TO MZ-BUS Rear left output (White) / Non-fading left output (White) Rear right output (Red) / Non-fading right output (Red) Front right output (Red) FM/AM antenna input DAB FM·AM TUNER 44W×4 AMPLIFIER HIDEAWAY UNIT KTC-1000R FM ANTENNA FRONT SPEAKER REAR SPEAKER TV MONITOR SUB WOOFER CHANGER SLAVE UNIT ANTENNA INPUT PREOUT REAR/NON-FAD FRONT POWER Antenna Conversion Adaptor (ISO­JASO) (Accessory8) Antenna Cord (ISO) (5. 5m) Antenna Cord (Accessory6) NOTE Route wiring away from power circuitry to avoid noise. Wiring harness (5. 5m) (Accessory5) Connector A Connector B 8 7 8 7 6 5 6 5 4 3 4 3 2 1 2 1 Automatic illumination control cable (Orange) ILLUMI Ignition cable (Red)+12V ACC ACC Fuse (3A) ACC Connect to control unit power supply terminal. Battery cable (Yellow)+12V BATT BATT Fuse (10A) BATT When using the optional power amplifier, connect to its power control terminal. Connect to the terminal that is grounded when either the telephone rings or during conversation. NOTE Power control cable (Blue/ White) P. CONT TEL mute cable (Brown) TEL MUTE To connect the KENWOOD navigation system, consult your navigation manual. Ground cable (Black) (To car chassis) If no connections are made, do not let the cable come out from the tab. 4 English 2WARNING Connecting the ISO Connector The pin arrangement for the ISO connectors depends on the type of vehicle you drive. Make sure to make the proper connections to prevent damage to the unit. The default connection for the wiring harness is described in 1 below. If the ISO connector pins are set as described in 2 or 3, make the connection as illustrated. Connector Function Guide Pin Numbers for Cable Colour ISO Connectors Functions 1 (Default setting) The A-7 pin (red) of the vehicle's ISO connector is linked with the ignition, and the A-4 pin (yellow) is connected to the constant power supply. A­7 Pin (Red) Ignition cable (Red) ACC BATT ACC BATT External Power Connector A­4 A­5 A­6 A­7 Speaker Connector B­1 B­2 B­3 B­4 B­5 B­6 B­7 B­8 Yellow Blue/White Orange Red Battery Power Control Dimmer Ignition (ACC) Vehicle Unit A­4 Pin (Yellow) Control unit Battery cable (Yellow) ACC BATT Purple Purple/Black Gray Gray/Black White White/Black Green Green/Black Rear Right (+) Rear Right (­) Front Right (+) Front Right (­) Front Left (+) Front Left (­) Rear Left (+) Rear Left (­) 2 The A-7 pin (red) of the vehicle's ISO connector is connected to the constant power supply, and the A-4 pin (yellow) is linked to the ignition. A­7 Pin (Red) Ignition cable (Red) ACC Vehicle ACC Unit BATT BATT A­4 Pin (Yellow) Control unit Battery cable (Yellow) ACC BATT 3 The A-7 pin (red) of the vehicle's ISO connector is not connected to anything, whilst the A-4 pin (yellow) is connected to the constant power supply (or both the A-7 (red) and A-4 (yellow) pins are connected to the constant power supply). Connect to a power source that can be turned on and | off with the ignition key. BATT Vehicle A­4 Pin (Yellow) Ignition cable (Red) BATT Unit Control unit Battery cable (Yellow) BATT English 5 Installation s When the control unit is the KVC-1000 Control unit (optional) KVC-1000 M4 IN OUT NAV I/F DAB control cable (Provided with the KTC-959DAB) KTC-1000R ANTENNA INPUT DAB DAB tuner (optional) KTC-959DAB Changer control cable (Provided with the C907) 2WARNING CD auto changer (optional) C907 Only connect black cable to TO 5L interface. [. . . ] · The ignition and battery cable are incorrectly connected. The following indications are used to inform you that there is a problem with the connections of the system. BUS-E01: The M-S switch of the Monitor connected to the BUS terminal is set to "M". The "MASTER SW" cable of the monitor power supply harness is connected to -. [. . . ]