User manual KENWOOD KVC-1000

[. . . ] 6. 5-Inch WIDE TELEVISION KVC-1000 INSTRUCTION MANUAL © PRINTED IN JAPAN B64-1454-00 (E)(+) 00/12 11 10 9 8 7 6 5 4 3 2 1 99/12 11 10 9 8 7 6 Contents English Before Use Safety Precautions . . 7 RDS Setting Screen News Bulletin Function with PTY News Timeout Setting . . 13 Audio Control Function Audio Control Screen -1 Adjusting the Balance and Fader Levels . . 14 TV Control Function TV Control Screen (Main) Selecting the Bands . [. . . ] Each time you touch [ SEEK ], the mode switches as follows. w FM1 P1 108 . 0 M Hz FM - I NFO ALM NEWS REG AF TI MANU ST PTY AUTO 1 w (Auto Seek Tuning) (Preset Station Seek Tuning) (Manual Tuning) AME MONO SEEK LO. S TI VOL AUTO 2 w 3 Auto Memory Entry You can automatically store all the receivable frequencies in the band currently being listened to, and then recall them with the touch of a button later. This function is especially useful when you are travelling and do not know what stations are available. Up to 6 frequencies can be stored this way. MANU 3Turning the Local Seek Function On/Off With the local seek function turned on, auto seek tuning skips stations with relatively poor reception. The LO. S indicator is displayed when the local seek function is on. 1 Select the band for auto memory entry. 2 Touch [ AME ]. [ ¢ ] and [ 4 ] blink. 3 Touch [ ¢ ] or [ 4 ] to start auto memory entry. The preset station numbers [ P1 ] - [ P6 ] are shown in order. When all the stations in a certain band are stored in the preset memory, the auto memory entry stops. The tuner then plays the last station received. NOTE · When the AF function is turned on whilst auto memory entry takes place, only RDS stations (i. e. , stations with RDS capability) are stored. RDS stations that have been preset for FM1 cannot also be preset in FM2 or FM3. · When the local seek function is turned whilst auto memory entry takes place, stations with poor reception are not stored. · When the Traffic Information function is on, only the local traffic information station frequency will be stored. 3Turning the Monaural Reception On/Off When poor stereo reception is experienced, this function will reduce noise and improve listening conditions. The MONO indicator is displayed when monaural reception is on. 19 FM/AM Tuner Control Function English Tuner Control Screen (Shift) 3 Traffic Information Function You can listen to traffic information. If you are listening to discs, they will continue playing until a traffic bulletin is broadcast. Turning TI function On/Off: Touch [ TI ] on the control screen to turn the function on and off. When a traffic information station is received, the TI indicator blinks. If you are listening to a disc when a traffic bulletin begins, playback will be interrupted. When the bulletin ends or poor reception causes signal losses , the disc will continue to play again. Switching to a Different Traffic Information Station: Use [ 4 ] / [ ¢ ] to make an auto seek of the TI stations in a certain band. NOTE · When you are listening to a disc, you cannot change to another TI station. · When the auto TP seek function is turned on and reception starts to weaken, the tuner automatically seeks stations with better reception. · If you are tuned to a station that is not a traffic information station itself but which provides EON services, you can still have traffic information received. 3 Presetting the Volume for Traffic Information/News Preset the volume to be used when traffic information/news starts to be broadcast. 1 Tune into the station for which you want to set the volume. 2 Adjust the volume to the desired level. 3 Keep touching [ TI VOL ] for two seconds or more. The volume level that the data has been stored. Future traffic information broadcasts are heard at the preset level. NOTE · The volume cannot be lowered by this function during tuner reception. The volume is only set when it is louder than the listening volume of the tuner. [. . . ] Secure cables using the supplied clampers. 4 After attaching the antenna with the double-sided tape, allow it to sit undisturbed for 24 hours. Take care not to apply force to the antenna or allow it to get wet during this time. 5 Wire the antenna cable to the hideaway unit. OFF ON BOOST OFF ACC Ignition key switch Battery Antenna parts Antenna unit Bundle cables with the clamper bar Rear window Accessory 8 Rear seat 33 Troubleshooting Guide English What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. PROBLEM The power does not turn on. POSSIBLE CAUSE The fuse has blown. SOLUTION After checking for short circuits in the cables, replace the fuse with one having the same rating. For safety reasons, the monitor does not open while the vehicle is moving. [. . . ]