User manual KENWOOD M-A100

[. . . ] The fuse cover must be refitted when replacing the fuse in the moulded plug. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or adapter, or consult your dealer. If nonetheless the mains plug is cut off, remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply. [. . . ] · If the left and right speakers are connected inversely or the speaker cords are connected with reversed polarity, the sound will be unnatural with ambiguous acoustic imaging. Be sure to connect the speakers correctly. Connection of parallel cord · When connecting the parallel cord, insert the plug straight into the connector until it clicks to lock them securely. · When disconnecting the parallel cord, push in the two sides of the plug and pull it straight out. Caution regarding placement (Except for U. S. A. and Canada) To maintain proper ventilation, be sure to leave a space around the unit (from the largest outer dimensions, including projections) equal to, or greater than shown below: Left and right panels: 10 cm, Rear panel: 10 cm Ventilation fan The ventilation fan runs during high-power reproduction. To allow for proper ventilation, do not block the ventilation fan. AC outlet on the rear panel UNSWITCHED AC outlet The power of the component connected to this kind of AC outlet can be switched ON/OFF regardless of the POWER switch on the main unit. Notes 1. Loose connections may prevent proper sound transmission or produce noise. Be sure to remove the power cord from the AC outlet before plugging or unplugging any connection cords. Plugging / unplugging connection cords without disconnecting the power cord can cause malfunctions and may damage the unit. Do not connect power cords from components whose power consumption is larger than what is indicated on the AC outlet at the rear of this unit. System connections M-A300/A100 (En) Connection of M-A300 Make connections as shown below. When connecting the related system components, refer also to the instruction manuals of the related components. Do not plug in the power lead until all connections are completed. AC outlet Surround speakers Right Left U. K. U. S. A. , Canada and China 5 -+ -+ Australia Other countries To AV control center CONNECT WITH AV CONTROL CENTER To AC wall outlet CENTER SURROUND FRONT UNSWITCHED SUB FRONT SURROUND WOOFER + R R SW + (6-16) C L L (6-16) SPEAKERS SPEAKERS When using the speaker system S-F700 Ventilation fan Center speaker See-through -+ White lined -+ Subwoofer Front speakers Right Left -+ -+ -+ -+ -+ Note The shape of the speakers are variable depending on the system and marketing destination type. System connections M-A300/A100 (En) 6 Connection of M-A100 Make connections as shown below. When connecting the related system components, refer also to the instruction manuals of the related components. Do not plug in the power lead until all connections are completed. AC outlet U. K. U. S. A. , Canada and China Australia Powered subwoofer Center speaker To AV control center -+ Other countries CONNECT WITH AV CONTROL CENTER SUB WOOFER To AC wall outlet CENTER FRONT UNSWITCHED FRONT SURROUND PRE OUT + (6-16) R R L + (6-16) C L (3-16) SPEAKERS SPEAKERS Ventilation fan Surround speakers Right Left See-through -+ -+ White lined Front speakers Right Left -+ -+ Note The shape of the speakers are variable depending on the system and marketing destination type. Operating instructions M-A300/A100 (En) 1 Switch the POWER key to ON position. POWER -ON ­OFF 7 2 Turn on the system by using the AV control center. · The power indicator on the panel lights up. 3 Play a music source. In case of difficulty What appears to be a malfunction may not always be serious. If your unit should not perform as expected, consult the table below to see if the problem can be corrected before seeking help from your dealer or service representative. Symptom Sound cannot be produced. (Indicator is off. ) Cause · The parallel cord is not connected. · The protection circuitry is activated due to internal temperature rise. Remedy · Connect them properly referring to "System connections". [. . . ] 105 dB Input sensitivity / impedance LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 V / 47 k Output level / impedance SUBWOOFER PREOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 (total 200 W max. ) Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]