User manual LA CROSSE TECHNOLOGY WS-7212U

[. . . ] (All remote temp/humidity sensors must be started before the indoor weather station) DO NOT PRESS ANY BUTTONS FOR 15 MINUTES. 2. 3. 4. In this time the indoor weather station and remote temperature/humidity sensor will start to communicate with each other, and the display will show both the indoor temperature and an outdoor 6 temperature and humidity. If the indoor weather station does not display both the indoor temperature and the outdoor temperature and humidity after the 15 minutes please re-try the set-up as shown on page 5. After both indoor temperature and outdoor temperature and humidity are displayed for 15 minutes you can place your remote temperature/humidity sensor outdoors and set your time. [. . . ] The following are some brief instructions for the basic set-up of remote sensor units with the WS7212U. These extra sensors can be purchased through the same dealer as this unit, or by contacting La Crosse Technology directly. A TX6 will monitor temperature only, a TX3U will monitor temperature and display the temperature on its LCD, the TX3UP will monitor the temperature via a probe for use in pools, spas, etc and the TX4U will monitor temperature and humidity. 15 Note: When setting up multiple units it is important to remove the batteries from all existing units in operation, then to insert batteries first into all the remote temperature/humidity sensor units, and in numeric sequence. Transmission problems will arise if this is not done correctly and if the total time for set-up exceeds 6 minutes. It is necessary to remove the batteries from all units currently in operation. In sequential order, install batteries (follow the same battery installation procedures seen in section "I" of the Detailed Set-Up Guide) into the 16 2. Follow the Detailed Set-Up Guide for programming and operating instructions. VIEWING AND OPERATING WITH MULTIPLE REMOTE SENSOR UNITS 7. To view the temperature of a different remote sensor unit, press and release the "CH" button. A shift from one "boxed" number to the next should be observed in the OUTDOOR LCD. 8. To view the Minimum/Maximum temperature: first select from which remote temperature/humidity sensor to read data from (indicated by the 17 "boxed" number). Pressing and releasing the "MIN/MAX" button will toggle through the minimum and maximum indoor temperature, and the minimum and maximum outdoor temperature. To reset the Minimum/Maximum readings, press and hold the "MIN/MAX" button for 5 seconds. MOUNTING Note: To achieve a true temperature reading, avoid mounting in direct sunlight. We recommend that you mount the remote temperature/ humidity sensor on an outside Northfacing wall. The sending range is 330 feet; obstacles such as walls, concrete, and large metal objects will reduce the range. Place both units in their desired location temporarily to test reception capability before permanently mounting. 3. REMOTE TEMPERATURE/ HUMIDITY SENSOR Remove the mounting bracket from the remote temperature/humidity sensor Mount using either screws or adhesive tape. Re-attach the remote temp/humidity sensor to the mounting bracket. B. The indoor weather station comes with the table stand already mounted. If you wish to use the table-stand, all that is required is to place the indoor weather station in your desired location. Remove the table stand by pulling down on the stand from the rear and rotating forward. 19 c. d. Place the indoor weather station onto the screw using the hanging hole on the backside. Gently pull the indoor weather station down to lock the indoor weather station into place. TROUBLESHOOTING NOTE: For problems not solved, please contact La Crosse Technology via e-mail or phone, or visit our website, www. lacrossetechnology. com Problem: The LCD is faint Solution: Replace batteries Problem: No outdoor temperature or humidity is displayed. [. . . ] THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC INFORMATION. Some States do no allow the exclusion of consequential or incidental damages therefore the above exclusion of limitation may not apply to you. For warranty work, technical support, or information contact: La Crosse Technology 2809 Losey Blvd. La Crosse, WI 54601 Phone: 608. 782. 1610 Fax: 608. 796. 1020 e-mail: support@lacrossetechnology. com (warranty work) sales@lacrossetechnology. com (information on other products) web: www. lacrossetechnology. com 29 FCC DISCLAIMER This device complies with part 15 of the FCC rules. [. . . ]