User manual LG HR835T

[. . . ] ENGLISH SIMPLE MANUAL Blu-ray Disc™/DVD Player with built-in HDD & HD Tuner Please read this manual carefully before operating your set and retain it for future reference. To view the instructions of advanced features, visit http://www. lg. com and then download Owner’s Manual. HR835T / HR832T 1 Getting Started 2 Getting Started Use of controls, adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure. To prevent direct exposure to laser beam, do not try to open the enclosure. [. . . ] yy Movie mode and finalized only yy Supports the dual layer disc also Finalized AVCHD format yy DVD±R/RW discs that contain Movie, Music or Photo files. yy ISO 9660+JOLIET, UDF and UDF Bridge format e Blu-ray y u i r o y u i r t y u i – – – REC DVD-ROM DVD-R DVD-RW DVD+R DVD+RW (8 cm, 12 cm) DVD-RW (VR) (8 cm, 12 cm) Audio CD (8 cm, 12 cm) CD-R/RW (8 cm, 12 cm) VR mode and finalized only Audio CD yy CD-R/RW discs that contain Movie, Music or Photo files. yy ISO 9660+JOLIET, UDF and UDF Bridge format Titles recorded via this unit Indicates special notes and operating features. TITLE/POPUP: Displays the DVD title menu or BD-ROM’s popup menu, if available. Battery Installation Getting Started 9 Front panel 1 Getting Started a Disc Tray b Display window c Remote Sensor d B (Open/Close) e T (Play/Pause) f I (Stop) g 1/!(Power) h USB Port Rear panel a ANTENNA IN b LAN port c HDMI OUT (TO TV) d DIGITAL AUDIO OUT (COAXIAL) e AC IN connector Connect the supplied power cord f ANTENNA OUT (TO TV) 10 Getting Started Connections to Your TV 1 HDMI Connection If you have a HDMI TV or monitor, you can connect it to this unit using a HDMI cable (Type A, High Speed HDMI™ Cable). Connect the HDMI jack on the unit to the HDMI jack on a HDMI compatible TV or monitor. Antenna connection to your TV and this unit Connect one end of the RF cable to ANTENNA OUT(TO TV) jack on the unit and other end to ANTENNA IN jack on your TV. Connect the Terrestrial TV antenna to the ANTENNA IN jack on the unit. If you want to use an indoor antenna, use one with a signal amplifier rated at 5V, 100mA and set [Antenna 5V] to [ON] in the setup menu. Getting Started Rear of this unit Rear of this unit Rear of this unit ANTENNA Rear of this unit HDMI Cable TV TV RF Cable TVTV Set the TV’s source to HDMI (refer to TV’s Owner’s manual). Getting Started 11 Resolution Setting The player provides several output resolutions for HDMI OUT jacks. The [Setup] menu appears. 1 Getting Started 3. Use w/s to select [DISPLAY] option then press d to move to the second level. 4. Use a/d to select the [Resolution] option then press ENTER (b) to move to the third level. 5. Use w/s to select the desired resolution then press ENTER (b) to confirm your selection. yy If your TV does not accept the resolution you have set on the player, you can set resolution to 576p as follows: 1. Press B to open the disc tray. 2. Press Z (STOP) for more than 5 seconds. Note , , 2 System Setting 12 System Setting Wired network connection Connect the unit’s LAN port to the corresponding port on your Modem or Router using a commercially available LAN or Ethernet cable (CAT5 or better with RJ45 connector). In the example configuration for wired connection below, this player would be able to access content from either of the PCs. Wired Network Setup If there is a DHCP server on the local area network (LAN) via wired connection, this player will automatically be allocated an IP address. After making the physical connection, a small number of home networks may require the player’s network setting to be adjusted. Adjust the [NETWORK] setting as follow. 2 System Setting Router Preparation Before setting the wired network, you need to connect the broadband internet to your home network. Broadband Service 1. Select [Connection Setting] option in the [Setup] menu then press ENTER (b). WAN LAN 1 PC LAN 2 LAN 3 PC LAN Cable 2. Use w/s/a/d to select the IP mode between [Dynamic] and [Static]. Normally, select [Dynamic] to allocate an IP address automatically. Rear of this unit If there is no DHCP server on the network and you want to set the IP address manually, select [Static] then set [IP Address], [Subnet Mask], [Gateway] and [DNS Server] using w/s/ a/d and numerical buttons. If you make a mistake while entering a number, press CLEAR to clear the highlighted part. Note , , System Setting 3. Select [OK] and press ENTER (b) to apply network settings. 5. If you select [Test] and press ENTER (b) at step 5 above, the network connection status is displayed on the screen. You can also test it on the [Connection Status] in the [Setup] menu. 13 Settings Adjust the Setup Settings You can change the settings of the player in the [Setup] menu. 1. Press HOME (n). 2 System Setting 2. Use a/d to select [Setup] and press ENTER (b). The [Setup] menu appears. 3. Use w/s to select the first setup option, and press d to move to the second level. 4. Use w/s to select a second setup option, and press ENTER (b) ) or d to move to the third level. 5. Use w/s to select a desired setting, and press ENTER (b) ) or d to confirm your selection. 14 Operating General Playback Using [HOME] menu To access numerous functions of the unit, press HOME on the remote. BACK (1): Exits the menu. Playing a Disc ert 1. Press B (OPEN/CLOSE), and place a disc on the disc tray. For the most Audio CD, BD-ROM and DVD-ROM discs, playback starts automatically. [. . . ] yy You are playing a disc recorded in a colour system that is different from your TV. yy Set the resolution to one that your TV accepts. Picture noise appears Sound Symptom There is no sound or the sound is distorted. Cause & Solution yy Connect the audio connection securely. yy The input source setting on the amplifier or the connection to the amplifier is incorrect. yy Check that the connected amplifier is compatible with the audio format output from the player. [. . . ]