User manual LG LSW420BX

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual LG LSW420BX. We hope that this LG LSW420BX user guide will be useful to you.


LG LSW420BX : Download the complete user guide (6967 Ko)

You may also download the following manuals related to this product:

   LG LSW420BX (6947 ko)

Manual abstract: user guide LG LSW420BX

Detailed instructions for use are in the User's Guide.

[. . . ] Do not wipe the product with a wet towel and do not use any heater or humidifier below where the product is installed. If water flows into the product or if moisture and heat are applied to the product, it can cause a fire, an electric shock or problem to the product. When drilling holes in the wall, always use a drill bit and drill of designated diameter. Also follow the designated directions for the depth of the hole. If the product is installed without following the designated method, the product may be unstable and cause a safety issue. Do not install the product near any object that may cause vibration. Do not install the product near any high voltage power cable or power source. Unplug the power cord from the power outlet before installing the product. If you install the product with the power cord plugged, it can cause an electric shock or a fire. Do not install the product with bare hands. Always wear proper work gloves. It can cause an injury. Do not allow the video connectors connected to the display to press against the wall. [. . . ] -  hen installing the product on wall material not designated, install the product so that each fixated location can withstand W the pull out load of 70kgf (686N) and shear load of 100kgf (980N) or above. Anchor a b c d e Wall mount screw - Use the Ø8mm drill bit for concrete and hammer (Impact) drill. Use a drill bit Ø8mm to drill a hole for the anchor location within a depth of 80mm ~ 100mm b. Set the wall mount on the wall by aligning to the location of the hole. Then, fasten the bolts at torque of 45 - 60 kgf/cm. 3 How to install the wall mount <When installing on a masonry wall> →  hen you separate the 8 screws on the wall mount connected to the wall bracket for use with a wooden wall, it is much easier W to install the product. A A →  hen installing the product on a masonry wall, turn the 8 W screws on the A part counterclockwise to separate the screw and bracket. →  fter aligning the wall bracket to the location to install, A mark the part to screw on the wall and then remove the wall bracket. Separate the wall mount screw. 4 Wall mount screw →  the screw cannot be assembled in the designated location If inevitably, it can be assembled by rearranging to the closest location. →  ssemble the wall mount screw on 2 left and 2 right location A on the top part and 1 left and 1 right location on the bottom part. →  t this time, use a "+" driver (Manual or motorized) or 8mm A wrench to tighten the screw so that the wall, wall bracket and screw are completely pressed against one another. <When mounting to wooden studs> 76mm drywall 406mm wood stud drywall a.  fter aligning the wall bracket on the wall where the center of the wood stud is marked, mark the location of the screws and A then remove the wall bracket. Use the 4mm drill bit for wood to drill holes with the depth of 76mm or above where the wall mount screw location is marked  on the wall. Tighten the wall mount screws for the wall bracket on the drilled hole. →  t this time, tighten the screw so that the wall, wall bracket and the wall mount screw are pressed against one another. A (Drywall can be damaged when tightened with excessive force, please be careful. ) →  hen tightening the screw use the "+" driver (Manual or motorized) or 8mm wrench. [. . . ] The wall mount has two screws that make minor adjustments to the level. ± 10mm(Leveling) 6 Cable arrangement and set protection cushion - Arrange the cables as shown in the picture. Use some type of cable banding device to hold all the cables together. -  ttach the set protection cushion to mitigate the impact between the wall and the set when adjusting the angle. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE LG LSW420BX




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual LG LSW420BX will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.