User manual LIFT-MASTER CPSII

[. . . ] When properly connected and aligned, the sensor will detect an obstacle in the path of its electronic beam. The sending eye (emitter with an amber indicator light) transmits an invisible light beam to the receiving eye (receiver with a green indicator light). If an obstruction breaks the light beam while the door is closing, the door will stop and reverse to full open position. [. . . ] · Attach bracket assemblies with 1/4"x1-1/2" lag screws (Figure 2). · Adjust right and left side bracket assemblies to the same distance out from mounting surface. Tighten the nuts securely. 1/4"-20 Lock Nuts "C" Wrap Mounting Bracket with Slot Mounting Bracket with Square Holes Figure 3 DOOR Track Installation Door Track Installation Procedure · Discard slotted bracket. Drill 3/8" holes in each track and fasten securely with hardware (Figure 3). Inside Wall Door Track 1/4" Lock Nuts Mounting Bracket with Square Holes Drill 3/8" Holes "C" Shaped Wrap 1/4-20x1/2" Carriage Bolts HARDWARE SHOWN ACTUAL SIZE Screw #10-32x3/8" Lock Nut #10x32 Lag Screw 1/4x1-1/2" Staples Carriage Bolts 1/4"-20x1/2" Lock Nut 1/4"-20 Figure 4 Alternate Wall Mount Inside Wall Mounting Bracket with Slot Mounting Bracket with Square Holes "C" Wrap Sensor with wire Indicator Light Floor Figure 5 Alternate Floor Mount Inside Wall Sensor with wire Indicator Light Mounting Bracket with Square Holes Mounting Bracket with Slot Attach with concrete anchors (not provided) "C" Wrap Floor 2 Bell Wire Secure Wire with Insulated Staples Connect Wire to Commercial Protector Interface Safety Sensor Beam 6" (15 cm) max. above floor Invisible Light Beam Protection Area Safety Sensor Beam 6" (15 cm) max. above floor MOUNTING AND WIRING THE SAFETY SENSORS · Insert the wire connector into each sensor and push until you hear a click. The white tab on the sensor should be flush with the back of connector. · Center each sensor unit in a "C" wrap with lenses pointing toward each other across the door. Finger tighten the wing nut on the receiving eye to allow for final adjustment. · For wiring connections, see following pages: CPS page 4 CPS-L page 4 CPSII page 5 Sensor Figure 6 Wing Nut "C" Wrap Wire Indicator Light 1/4-20 x 1-1/2" Hex Bolt HARDWARE SHOWN ACTUAL SIZE 1/4-20x1-1/2" Hex Bolt Wing Nut ALIGNING THE SAFETY SENSORS · Power up the opener. Green indicator lights in both the sending and receiving eyes will glow steadily if wiring connections and alignment are correct. If the receiving eye indicator light is not glowing steadily (and the invisible light beam path is not obstructed), alignment is required. · Loosen the receiving eye wing nut to allow slight rotation of unit. Adjust sensor vertically and/or horizontally until the green indicator light glows steadily. · When indicator lights are glowing steadily in both units, tighten the wing nut in the receiving eye unit. 3 CPS Wiring Connections Commercial Protector Interface 24V Common CDO Sensing Edge Input Sensor White To Sending Eye (Emitter) and Receiving Eye (Receiver) Sensor White/Black WARNING CPS-L Wiring Connections for use with Solid State II (Logic Control Board Ver 2) CAUTION Once eyes are connected it will be necessary to set DIP switch to Timer to Close mode (refer to "Activate Photo Eyes" instructions below). Logic 2 Shown White White/Black TO ACTIVATE SAFETY SENSOR EYES 1. Starting with the door in the close position, run the door through one full open-close cycle to "Learn" the sensor eyes. [. . . ] NOTE: For non-solid state operators, if the door is stopped in a mid position, activation of the sensors will cause the door to open. CPS-L Only: If the sending eye and receiving eye indicator lights are both lit but interrupting the photo eyes does not cause the door to reverse when closing, refer to "To Activate Safety Sensor Eyes" on page 4. 6 Replacement Parts CPS CPSII Commercial Protector Interface . . 001A5053-9 CPS / CPSII / CPS-L How to Order Repair Parts Our large service organization spans America. [. . . ]