User manual LIFT-MASTER CPSII-N4

[. . . ] CDO Protector System® OWNER'S MANUAL Models: CPS-N4, CPSII-N4 and CPS-LN4 WARNING This device is for use ONLY with LiftMaster Commercial Door Operators. Use on other than recommended equipment voids warranty, and may cause PROPERTY DAMAGE or SERIOUS PERSONAL INJURY. Have door in full open or closed position and disconnect power to the garage door opener BEFORE installing the CDO Commercial Protector System®. WARNING WARNING CAUTION Installation procedures are the same for all door types. --Left Side of Garage-- -- Right Side of Garage -- Safety Reversing Sensor Invisible Light Beam Protection Area Safety Reversing Sensor Facing the door from inside the garage Install the Commercial Protector System® IMPORTANT INFORMATION ABOUT THE SAFETY REVERSING SENSOR Be sure power to the opener is disconnected. [. . . ] For sensing above 6" (15 cm), a second set of eyes would be required. Figure 1 Wall or Floor Mounting Hex Mounting Nut for Sensor Lock Washer for Sensor Floor or Wall Mount For typical floor or wall mounting applications see Figure 1. If necessary, see Figure 2 for various assembly options to fit your application. NOTE: Putting track bolts in slots will prevent brackets from pivoting. To attach to concrete use concrete anchors (not provided). 1/4"-20 x 5/8" Track Bolts Track Mount To mount to door track use only one bracket per side (Figure 3). 1/4"-20 x 5/8" Track Bolts 1/4" Flat Washer 1/4" Lock Washer 1/4"-20 Hex Nut 1/4" x 1-1/2" Lag Screws Figure 2 Assembly Variations Assemble to either side Flip one bracket and assemble to either side Figure 3 Door Track Mounting 1/4" Flat Washer 1/4" Lock Washer 1/4"-20 Hex Nut 1/4" Lock Washer 1/4"-20 Hex Nut Door 1/4" Drill Holes 1/2" Hole Spacing 2" Hole Spacing 1/4"-20 x 5/8" Track Bolts To attach vertically to 2" x 4" wall stud and prevent wood from splitting, bracket may also be rotated with leg on top. Shown with leg on bottom. CONDUIT CONNECTIONS Use a liquid tight fitting (1/2" trade size) with sealing washer to connect to sensors. We recommend the use of a liquid tight junction box near each sensor to make the connection to the sensor leads. Use rigid or flexible liquid tight conduit (depending on local codes) from junction boxes to operator. copper wire for connection between the sensors and the operator. Liquid Tight Junction Box Liquid Tight Conduit WIRING CONNECTIONS CPS-N4: See top of page 3 CPSII-N4: See middle of page 3 CPS-LN4: See page 4 and 5 See Wiring Connections Sensor Beam 6" (15 cm) max. above floor Liquid Tight Junction Box Invisible Light Beam Protection Area Sensor Beam 6" (15 cm) max. above floor Figure 4 2 CPS-N4 Wiring Connections Commercial Protector Interface 24V Common Sensor Brown Sensor Blue CDO Sensing Edge Input To Sending Eye (Emitter) and Receiving Eye (Receiver) CPSII-N4 Wiring Connections for use with Solid State Logic Control Board CPSII Option PCB Terminals Green Lights Insert PCB into any or four slots IR Protector Only A B C D E F G H I J CDO Motherboard IR Protector and 2-Wire Fail Safe Door Edge IR Protector and 4-Wire Fail Safe Door Edge A B C D E F G H I J A B C D E F G H I J NOTE: Logic 2 Board will have the same connection. 3 CPS-LN4 Wiring Connections for use with Solid State II (Logic Control Board Ver 2) Blue Brown TO ACTIVATE SAFETY SENSOR EYES ON ON SET TIMER TO CLOSE 1 2 3 4 1. Run the door through one full close-open-close cycle to "Learn" the sensor eyes. NOTE: Test the Safety Sensor Eyes operation by interrupting the eyes while closing the door. Once the sensor eyes are "Learned" and it becomes necessary to remove the sensors, the sensors will need to be "unlearned" by setting DIP switch to "Timer to Close" mode and pressing the Close Button. CPS-LN4 Wiring Connections for use with LGO Operator IR PROTECTOR ONLY IR PROTECTOR AND SAFETY EDGE Important Note: When sensors (IRs) are used, wiring mode B2 must be reprogrammed. See LGO owner's manual for further information. 4 CPS-N4 Wiring Connections for use with LiftMaster Operators Featuring Estate Series X3 or B3 Control Board CPS-N4 Wiring Connections for use with LiftMaster Operators Featuring GL Control Board 5 Testing the Protector System® WARNING Without a properly working CDO Commercial Protector System , persons (particularly children) could be SERIOUSLY INJURED or KILLED by a closing garage door. [. . . ] . 50-15515 CPS-N4 / CPSII-N4 / CPS-LN4 How to Order Repair Parts Our large service organization spans America. Monday through Saturday When ordering repair parts, please supply the following information: PART NUMBER DESCRIPTION MODEL NUMBER Address orders to: THE CHAMBERLAIN GROUP, INC. Country Club Road Tucson, Arizona 85706 7 01-16013K © 2005, The Chamberlain Group, Inc. [. . . ]