User manual LIFT-MASTER CROWN JEWEL PROGRAMMING

[. . . ] Elmhurst, IL 60125-1196 www. chamberlain. com Crown Jewel Telephone entry system 1 23 456 789 0# G UP CALL 1 23 456 789 0# G UP CALL Keypad Programming Manual Table of Contents Quick Reference Guide Programming Basics 2-3 4-5 Visitor Calls 18-20 Procedure for Programming . 20 Configure Relays Entry Codes 7-8 9-10 Configure Relay #2 and Status #2 Input . 10 Direct Commands 21-22 Direct Commands from Resident's Phone 23-24 Security Features 25-26 Change Password . 26 Time Zones [Schedules], Holidays 11 Set the System Clock . [. . . ] The pound key (#) MUST be used to SAVE the data at the end of each programming step. Time MUST be entered using a 24-Hour format (8:00 AM = 0800, 3:00 PM = 1500 etc. ) 2 Short Beeps: Programming input is valid 1 Long Beep: Input is not valid. PAGE 15 Call Forwarding The Call Forwarding feature redirects visitor calls to an outside telephone number instead of ringing the house. The forwarding number is a regular phone number of up to 12-digits in length. You may also attach one of the following features to a forwarding number: · An extension of an automated switch board · An extension (up to 6 digits) that the visitor can dial from the unit's keypad. Setting the Call Forwarding Number - 14 1. 3 NOTE: During a Call Forwarding call, the visitor will hear normal telephone line sounds, however, they will not hear the number being dialed. 1. Press Enabling/Disabling Call Forwarding - 13 FACTORY SETTING: 0 (Disabled) NOTE: To use the Call Forwarding feature, you MUST program a Call Forwarding Telephone Number. . Enable/Disable Call Forwaring Mode: 0 = Disable Call Forwarding 1 = Enable Call Forwarding 2 = Enable Scheduled Call Forwarding 3. IMPORTANT NOTES: If you make an error during an entry, press the asterisk key () to begin again. The pound key (#) MUST be used to SAVE the data at the end of each programming step. Time MUST be entered using a 24-Hour format (8:00 AM = 0800, 3:00 PM = 1500 etc. ) 2 Short Beeps: Programming input is valid 1 Long Beep: Input is not valid. PAGE 16 Setting the Call Forwarding Extension - 16 When the Call Forwarding feature is enabled, the Crown Jewel is able to dial an extension number (up to 6-digits). Press EXAMPLE: 1 2 3 Sets the Call Forwarding Extension Number as 1234. Setting the Call Forwarding Extension Delay - 15 1. Press EXAMPLE: 1 2 3 Sets a pause of 30 seconds between the Call Forwarding number and the Call Forwarding Extension number. Set the Call Forwarding Schedule - 18 Program calls to be forward during specified times and days. 1. Enter Days of the Week (To add one or more days to the Time Zone/Segment, press the digit corresponding to the day) : 1 = Sunday 2 = Monday 3 = Tuesday 4 = Wednesday 5 = Thursday 6 = Friday 7 = Saturday 8 = Holiday 3. Enter Holiday Option 0 = No Schedule on Holidays 1 = Use Same Schedule on Holidays 2 = Use Schedule Number 8 when this day falls on a Programmed Holiday 6. Press EXAMPLE: 1 2 3 4 5 6 Enables the Call Forwarding Schedule to contact the Call Forwaring Number on Thursdays from 9:00 AM to 5:00 PM excluding Holidays. PAGE 17 Visitor Calls When a visitor contacts a resident with the Crown Jewel , the resident can preform various functions using their touch-tone phone. The default settings are as follows: KEYS ON RESIDENT'S TELEPHONE WXYZ Activates Relay #1 JKL Extends Talk Time Hang Up and Deny Access to the Visitor Activates Relay #2 ABC Toggles Between Visitor and Another Phone Call Change the Visitor Call Response Keys - 34 1. Press EXAMPLE: 1 2 3 4 5 6 7 Changes the phone key that operates Relay #1 to "1", Relay #2 to "2", the phone key that toggles between calls to "6", "7" extends talk time and "8" hangs up and denies access to the visitor. NOTE: The asterisk key ( ) may be assigned to a specific phone key response, therefore, you will be UNABLE to cancel a command in this programming step. Set Visitor Call Ring Sound - 06 FACTORY SETTING: 2 (Double Ring) 1. The phone will ring once every 6 seconds during a visitor call. Set Max Visitor Call Ring Count - 12 Sets number of rings (1-24) the unit will allow before it disconnects the call. Press EXAMPLE: 1 2 3 Sets the number of rings before the Crown Jewel disconnects to 10 rings. IMPORTANT NOTES: If you make an error during an entry, press the asterisk key () to begin again. [. . . ] PAGE 28 Other System Settings Rings Before Answer - 29 Sets the number of rings before the Crown Jewel will answer a call from a remote telephone. If you have an answering machine (or answering service) attached to the same telephone line as the unit, set the Crown Jewel count for two (2) or more rings higher than the answering machine/service count. FACTORY SETTING: 5 Rings 1. Press EXAMPLE: 1 2 3 The Crown Jewel unit will answer the call after 6 rings from a remote telephone. Set Alternate Prefix - 36 a remote telephone. after 6 rings from When you press either "##" or "QQQ" on the resident phone, the Crown Jewel will look for Direct Commands or Programming and it disconnects the phone line and waits for a command. [. . . ]