User manual NIKON SU-800

[. . . ] En Nikon Close-up Speedlight Commander Kit R1C1 R1 Nikon Close-up Speedlight Remote Kit SU-800 SB-R200 Wireless Remote Speedlight Wireless Speedlight Commander Instruction Manual For your safety Before using your product, please read the following safety precautions carefully and thoroughly to ensure correct and safe use and to help prevent damage to your Nikon product or injury to yourself or others. For quick reference by those who use the product, please keep these safety instructions near the product. In this manual, safety instructions are indicated with these symbols: WARNING in personal injury, or death and property damage. CAUTION Disregarding instructions marked with this symbol could result Disregarding instructions marked with this symbol could result in property damage. WARNINGS for the Wireless Speedlight Commander SU-800 and the Wireless Remote Speedlight SB-R200 1 If corrosive liquids seep from the batteries and get in your eyes, immediately wash your eyes with running water and consult with a doctor. 2 If corrosive liquids seep from the batteries and come in contact with your skin or clothes, wash immediately with running water. [. . . ] Press the [MODE] button to set the flash mode to TTL or M (manual). · "TTL" is preset when shipped from the factory. · Only the M (manual) flash mode is available for Group C. A B MODE NO AF-ILL A B ON/OFF 4 SEL READY LOCK Setting the SB-R200 to fire or cancel. Press the [A B] select button to set flash firing/ canceled for Group A or B. · The flash-canceled group name disappears. · You can cancel flash firing for Groups A and B, but not for Group C. · Once set to flash canceled mode, flash output-level ratio in TTL mode becomes invalid, while the flash output level compensation values are retained. · Even if the flash mode is set to flash canceled, flash output level compensation values in the M (manual) mode are retained. 74 5 Setting the SB-R200's flash output level ratio between Groups A and B (in TTL mode). Press the [SEL](FUNC. ) button to display flash output level ratio (blinking), then press the [] or [] button to increase or decrease the ratio. Press the [SEL](FUNC. ) button once again and the flash output level ratio stops blinking. The last value to blink is the one that has been set automatically. · The flash output level ratio can be set from 8:1 to 1:8. · As the ratio changes, the flash output level indicator bar varies. · Continuously pressing the [] or [] button quickly increases or decreases the ratio. · The flash output level ratio blinks during adjustment and stops after blinking six times unless an adjustment is made. The last value to blink is the one that has been set automatically. 6 · The same flash output level compensation value is set for both Groups A and B. · The flash output level compensation values can be set in 1/3 step increments or decrements from +3. 0 to -3. 0 EV. · The values are displayed in decimal format, like 0. 3 for 1/3, and 0. 7 for 2/3. · Continuously pressing the [] or [] button quickly increases or decreases the value. · The flash output level blinks during adjustment and stops after blinking six times unless an adjustment is made. The last value to blink is the one that has been set automatically. Setting the SB-R200's flash output level compensation value (in TTL mode). Press the [SEL](FUNC. ) button to display the flash output level compensation value (blinking). Press the [] or [] button to increase or decrease the compensation value. Press the [SEL](FUNC. ) button once again and the flash output level stops blinking. The last value to blink is the one that has been set automatically. Details on close-up flash operation and shooting procedures 75 3 Procedures for close-up flash operation 7 Setting the manual flash output level for group C. [. . . ] 600µs Dedicated shoe for Attachment Ring SX-1 or Speedlight Stand AS-20 White LED Ready-light One CR123A (3V) lithium battery Approx. 80 x 75 x 55mm (3. 1 x 3. 0 x 2. 2 in. ) These performance specifications are applicable when a fresh battery is used at normal temperatures (20°C/68°F). Specifications and design are subject to change without notice. 131 Reference information 9 Index · For Speedlight parts, icons etc. on the LCD panel, refer to "Speedlight parts, their functions, and accessories" (p. [. . . ]