User manual NOVY 7901

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual NOVY 7901. We hope that this NOVY 7901 user guide will be useful to you.


NOVY 7901 : Download the complete user guide (266 Ko)

Manual abstract: user guide NOVY 7901

Detailed instructions for use are in the User's Guide.

[. . . ] €¢ B: Turn the electronics box by removing the 4 screws and by placing back the box upside down (cables facing up). €¢ C: Turn the outlet 180° again with the 8 screws. 052), this should be mounted first unto UP_SIDE, before placing UP_SIDE into the table top (more information about the adapter 7901. 1 SURFACE MOUNTING Stick the delivered grey insulating tape (661-050) on the edge of the opening. [. . . ] €¢ In case of an exhaust pipe through the outside wall, use the outside wall grate type MGE. When using a flat exhaust duct: • Use flat ducts with rounded corners and air conductors in the bends. €¢ In case of restricted space in the cabinet, you can order an adapter as an option (item number 7901. €¢ Make use of the connecting piece when connecting the flat duct to the outlet of the UP_SIDE. General: • Make the duct as short as possible and with as few as possible bends to the outside. €¢ If an exhaust pipe through the outside wall passes a cavity wall, make sure that the exhaust duct fully bridges the cavity and slightly declines to the outside. €¢ In case of an exhaust pipe through the roof, use a double-walled roof passage with sufficient width. Fresh air can be supplied by slightly opening a window or an outside door or by installing an inlet grate. €¢ Use the delivered white insulating tape for an airtight seal (801-006). 4 APPLIANCE ADJACENT TO THE UP_SIDE For surface mounting and flush mounting • On the appliance that is not placed above the motor casing of UP_SIDE the delivered black PVC strip (7900-094) must be applied at the front and the rear. For surface mounting: • Place the domino and/or induction hotplate besiUP_SIDE. For flush mounting: • Place the appliance(s) besiUP_SIDE. The drip tray is just not touching the decorative frame of the UP_SIDE. EN 23 3 ADJUST THE SUCTION UNIT OF UP_SIDE By default the click system is properly adjusted such, that the suction unit (990984) locks into place in the suction opening. Adjust the click system (only in the following cases): Suction unit (C) does not stay down = distance between A and B too large Suction unit (C) cannot be fully pushed down = distance between A and B too small If adjustment is still required, follow this instruction. Adjust the click system (A) and the hook (B): • Remove the suction unit (C) from the hood and remove the lid (D) from the box. €¢ Slightly unscrew the 4 capped nuts, so you can slide the foot (E) together with the click system (A) into the longitudinal direction. €¢ Place the suction unit (C) back and push it fully downwards. €¢ Press the foot (E) together with the click system (A) until it is against the hook (B). 4 ELECTRICAL CONNECTION Set the selector switch to ‘position II’ (this is the default setting). [. . . ] Use sealant (not supplied) to close the gaps between UP_SIDE, the work surface and the other appliances. 052) The adapter makes it possible to continue with a flat duct directly from the cooking hood. In case of a cabinet with a limited depth, this adapter is the ultimate solution to allow installation with flat ducts. The adapter is mounted unto the outlet of UP_ SIDE to which a flat duct can be connected directly. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE NOVY 7901




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual NOVY 7901 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.