User manual OMNIMOUNT CLSP INSTALL

[. . . ] Warranty does not apply to products which have been lost, damaged by misuse, abuse, or accident. OmniMount Systems, Inc. 8201 South 48th Street · Phoenix, AZ 85044-5355 1-800-MOUNT-IT · www. omnimount. com Designed for Flat Panel TV's up to 24" Maximum Weight Capacity: 30 lbs. (13. 6 Kg) VESA compliant: VESA 75/100 Installation Template Included Integrated Cable Management Lift N' Lock Installation Questions?Call 1-800-MOUNT-IT (USA only) PN: 1002786--Rev A 7/2005 8 IMPORTANT · Do not begin the installation of your OmniMount product until you have thoroughly reviewed this document and understand the instructions. Step 7 -- Adjusting the Display The Wishbone series cantilevers provide a wealth of display adjustment to offer the best viewing from a number of seating positions. · · · · We highly recommend that this product be installed by a qualified professional. [. . . ] Cables can only be installed in the recessed cable channel. Step 2 -- The Installation Template The Installation Template is designed to make the installation of the CL-S faster, easier and more accurate. The template also includes a built in dust channel to reduce the clean up chores from mounting the CL-S. Assembling the Dust Channel: Locate the supplied mounting template. 1 9. 2 To install cables, you'll first need to remove the cable cover from over the recessed cable channel . Using a Phillips Head screwdriver, remove the Retaining Screw (9. 1) and Cable Cover (9. 2) and set these parts aside until later. Note: Cable Covers and Retaining Screws do not need to be removed from flat side to install cables. Fig. 9 Step 3 -- Mounting to the Wall 9. 1 Follow the instructions based upon your mounting surface: 3a Wooden Stud 3b Concrete/Masonry 3c Cinder Block Fig. 2 To simplify the cable installation process, route the cables through one arm section, and then re-attach the cable covers before proceeding to the next arm section. Step 3a -- Mounting to Wooden Studs The CL-S can be mounted on a single wooden stud. Using an electronic stud finder (Fig 2), locate the center of the wooden stud at the desired mounting location. Extend the stud center line, and then draw a horizontal line where you wish the center of the screen to be located. Remove the four square perforations above center hole to help align the template with the center mark of the stud. Using a bubble level, level the guide, and then press the adhesive backing against the wall to hold the guide in place. Using a 1/8" (3mm) drill bit, drill 2 pilot holes 1. 5" (40 mm) deep into the center of the studs, through the circular cut-out sections of the installation template. Note: For best results from the dust channel, press and hold the template against the wall about 2" (50 mm) from where you are drilling. Note: Be sure to hold the guide in an upright position so as not to spill the collected dust. Note: To reduce signal interference OmniMount recommends that the power cable be installed on the lower arm and A/V cables be installed on the upper arm. If an RF cable needs to be installed, installation on the lower arm is recommended. To install the A/C Power Cable (10. 1), run the wire through the Lower Arm's recessed cable channel (10. 2) and then attach it directly to the display. DO NOT run these through the Front Arm (10. 4). To install other A/V cables, route the cables into the Recessed Section of the Upper Arm (10. 5). Then, route the cables around (10. 6) to the recessed section on the opposite side of the Front Arm (10. 4). Note: Be sure to leave some slack in the cable so that the arm assembly can move freely without stretching or damaging the cables. Step 3b -- Mounting to Concrete/Masonry Fig. 10 10. 6 The CL-S can be mounted directly to concrete/masonry walls. Fig. Concrete must be 2000 PSI density minimum. 10. 2 10. 5 Remove the tape strip from the back of the template, and place the template in the desired location. Using a bubble level, hold the template in a level position and then press the adhesive backing against the wall to hold the guide in place. Note: Depending upon the roughness of the surface, you may need to hold the template in place with an additional application of tape or blue painter's tape. [. . . ] Note: For best results from the dust channel, press and hold the template against the wall about 2" (50 mm) from where you are drilling. Note: Be sure to hold the guide in an upright position so as not to spill the collected dust. Insert wall anchors into the mounting holes, and lightly tap them flush to the wall with a hammer. (Fig 3) VESA 100 VESA 75 The Mounting Head of the CL-S is VESA compliant, and supports the following VESA Patterns (Fig. [. . . ]