User manual OPTICON OPR 3101

[. . . ] Rugged Wireless Laser Barcode Scanner OPR 3101 The OPR 3101 scanner uses Bluetooth technology for wireless transmission of scanned barcode data. Specifications Manual Opticon OPR 3101 Specifications Manual All information subject to change without notice. Document History Model Number: Edition: Date: OPR 3101 1A 2009-08-31 Specification Number: Original Spec Number: SS07028 SS07012 Copyright 2007 Opticon. All rights reserved. This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic or machine readable form without prior written consent of Opticon. Limited Warranty and Disclaimers PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING OR USING THE PRODUCT. This official registration number is directly related to the device purchased. Removing the serial number voids the warranty. Warranty Unless otherwise agreed in a written contract, all Opticon products are warranted against defects in materials and workmanship for two years after purchase. [. . . ] Charging Current Parameter CRD-3101 while charging 200 mA or lower Testing Conditions Specification 500 mA or lower Note When connected to RS-232C (when using AC adaptor) Output: 6 V, 750 mA When connected to USB, use high power port (500 mA). Operating temperature: 25° C Charging Temperature: 0 to 40° C Battery charging operation may be stopped when the scanner is charged at the temperature higher than 40° C. Battery charging operation may be stopped when the power supply voltage impressed to the charging terminals exceeds the range of 3 to 6 V. Note: Model names of AC adaptors dedicated to CHG-3101 and CRD-3101. - Model for OSE and OPTICON: GP-ACGN13T-K4-2 - Model for Japan and North American Market: GP-ACGN13U-K4-2 5. 5. Battery Operating Time and Charging Time Parameter Idle 1 Battery Life Idle 2 In use Charging time 1 Charging time 2 Specification About 55 hours About 48 hours About 25 hours About 5 hours About 10 hours Note Without connection to communication line. Without connection to communication line and scanning once in every 5 seconds. When using CRD-3101 and connected to USB (bus power supply). Charging Time Note: Battery life may be shorter than specified above when the quality of the battery pack is degraded. 11 Opticon OPR 3101 Specifications Manual 5. 6. LED Indicators The OPR 3101 signals its operating status with LEDs. Status Charging Color Red Green Blue Display Lighting Lighting Operating Status Shows that the scanner is being charged. Shows a successful completion of scanning or data transmission. Scanning Red Green Blinking Shows a failure or error in data transmission. Shows that the scanned data is being stored to the memory of the scanner. Wireless Connection Blue Blinking Shows that the scanner is making a connection to wireless communication line. Shows a failure or error in making a connection to a wireless communication line. Shows that the scanner has disconnected the wireless communication line. Red Lighting Lighting Wireless Disconnected Red Lighting Shows that the wireless communication is disconnected because the scanner is outside the communication range. The scanner must be charged. Low Battery Level Red Blinking 12 Opticon OPR 3101 Specifications Manual 6. Laser Scan Specifications Parameter Light-emitting element Emission wavelength Light output Scanning method Scanning speed Scan angle Specification Red laser diode 650 ±10 (25° C) 1. 0 or less Bi-directional scanning 100 ±20 Scan angle: 54 ±5 Read angle: 44 (Min) Unit -- nm mW -- scans/s ° ° mm Auto-trigger IR detection area 40 Notes: Refer to chapter 14, "Trigger and Read Options, " to read about the scan modes. Refer to chapter 7, "Technical Specifications, " to read about scanning performance. 6. 2. Laser Scan Tilt Laser scanning tilt is the vertical difference between both ends of a laser scan line. · Less than 1. 2° angle in vertical direction from the scan origin (mirror motor). · Up to 3. 1 mm when measured at a point 150 mm from the scan origin. Curvature of Scan The maximum difference between the laser scan line and the line between both ends of the laser scan line. · Up to 1. 27° angle in vertical direction from the scan origin (mirror motor). · Up to 3. 3 mm curvature when measured at a point 150 mm away from the scan origin. 13 Opticon OPR 3101 Specifications Manual Figure 3: Laser scan tilt and curvature 7. Technical Specifications The conditions for technical specifications are as follows, unless otherwise specified in each section. Conditions Ambient temperature and humidity: Ambient light: Background: Room temperature (5 to 35º C) Room humidity (45% to 85% RH) 500 to 900 lx Barcode = black Space = white Margin = white Background of label = black 3. 7 V Approve the performance when decoding is successful in all ten tests. [. . . ] This mode is mainly used for demonstration and diagnosis. · Conditions Moving speed Angle Environmental temperature and humidity Environmental illuminance Conditions for the auto trigger 100 ±10 mm/s (the moving direction is not specified) Vertical to the edge of the scanner Room temperature and humidity 500 to 900 lx 1. Barcode sheet: OPTOELECTRONICS Test Sheet (white) Background: OPTOELECTRONICS Test Sheet (black) 2. Barcode sheet: OPTOELECTRONICS Test Sheet (black) Background: OPTOELECTRONICS Test Sheet (white) Figure 13: Auto trigger detection area 31 Opticon OPR 3101 Specifications Manual 14. 3. Auto Trigger Settings Functions SET Disable auto trigger Enable auto trigger END Menu labels Menu codes ZZ +F +I ZZ _ZZ_ _+F_ _+I_ _ZZ_ 15. [. . . ]