User manual PALSONIC MODEL 5110PF

[. . . ] In order to wipe dust off the picture tube or off the cabinet, you should remove the power plug from the wall outlet first. You can wipe lightly with a piece of dry, clean, soft cloth. Do not expose the TV set to rain or excessive moisture, to prevent tire disaster or electric shock. Do not remove the cover to avoid danger. The TV set should be placed on an adequate place without exposing it to direct sunlight and other sources of heat to prevent the deformation of the cabinet or damage to components. Keep a space of more than 5cm from the walls to the TV set, to guarantee the good ventilation. When the TV set is to be left unattended, please turn off the power switch and remove the plug from the wall outlet. When the power cord or the plug is damaged, please contact a qualified service department to get service. 2 Installation Antenna Connection To ensure a bright-coloured and clear picture, you should use an outdoor aerial or CATV cable. [. . . ] It is convenient to set the channel numbers to the same position numbers using MANUAL SEARCH and SKIP functions. To preset channels (Manual search) Manual search If AUTO SEARCH can not preset the desired channels, or you want to preset the desired channels one by one with the preferred channel numbers, please make use of Manual search. Enter into POS. MEMORY menu, press the or button to select and highlight POSITION. Note: press the or button to select a channel number within 0. 7 second. Press and hold the or button for over 0. 7 second to select a decimal number. POS. MEMORY POSITION 01 BAND VHFL SKIP OFF SEARCH DOWN MFT DOWN AUTO MEMORY !!!!!!. . . . . . 2. Press the button to search channels from current channel to higher channel. Press the button to search channels from current channel to lower channel. When a channel is located, the searching stops, this channel is then memorised with the preset channel number. POS. MEMORY POSITION 01 BAND VHFL SKIP OFF SEARCH DOWN MFT DOWN AUTO MEMORY !!!!!!. . . . . . Note: you can also make use of BAND selection to quicken the searching process in your desired band. Pressing the or button moves the band to the next step in the sequence below. POS. MEMORY POSITION 01 BAND VHFL SKIP OFF SEARCH DOWN MFT DOWN AUTO MEMORY VHFL VHFH UHF !!!!!!. . . . . . 3. When you want to store another channel with another position, repeat steps 1 & 2 above. 8 OPERATION Tuning in (continued) To skip unnecessary position numbers and MFT (Manual Fine Tuning) To skip a position number After presetting the channels, you can skip unnecessary position numbers so that only the channels you want to watch are selected. MEMORY menu, select and highlight BAND VHFL SKIP OFF POSITION, then select the unwanted program number with the SEARCH DOWN MFT DOWN or button. AUTO MEMORY !!!!!!. . . . . . 2. Press the or button to select "SKIP ON" After completion of channel preset, the position number will then be skipped when you select channels with the CH button. If you want to skip other unwanted channels, repeat step 1 above to change the channel number. To restore a skipped position number Select the position number you want to restore. MFT (Manual Fine Tuning) POS. MEMORY POSITION 01 BAND VHFL SKIP OFF SEARCH DOWN MFT DOWN AUTO MEMORY !!!!!!. . . . . . button to move the cursor to When sound and picture's effect of a channel is poor (for example: one or two CATV channel's sound and picture are not standard), you can correct them by making use of Manual Fine Tuning). Enter into POS. MEMORY menu, select the channel you want to manually fine tune. POS. MEMORY POSITION 01 BAND VHFL SKIP OFF SEARCH DOWN MFT DOWN AUTO MEMORY !!!!!!. . . . . . 2. Press the or button to select and highlight MFT, then press the or button, the channel begins fine tuning until the optimum picture and sound is achieved. Note: if some channel's colour is abnormal, it may be that the setting of the colour system is wrong, please do adjustment according to The setting of colour (on page 10) to set the colour system. To exit the menu, press the MENU button repeatedly. POS. MEMORY POSITION 01 BAND VHFL SKIP OFF SEARCH DOWN MFT DOWN AUTO MEMORY !!!!!!. . . . . . 9 OPERATION Tuning in (continued) The setting of colour and sound system 1. MEMORY1, MEMORY2, MEMORY3 and MEMORY 4 (user-set) can be selected cyclically. MEMORY 1 MEMORY 2 MEMORY 3 MEMORY 4 PICTURE COLOR BRIGHT CONT SHARP BB SELECT PICTURE COLOR BRIGHT CONT SHARP BB SELECT To set the desired picture quality to the MEMORY position 1. Or press the P. M button, the picture control menu appears. 50 50 100 50 ON ADJUST 2. Press the or and press the button to select the desired adjusting item, or button to adjust the level. 50 70 100 50 ON ADJUST Pressing (MEMORY 4) Item COLOR BRIGHTNESS CONTRAST SHARPNESS *TINT B. B (blue back) paler darker weaker softer purplish deeper lighter stronger sharper greenish MEMORY1 50 50 100 50 MEMORY2 MEMORY3 50 50 50 50 50 50 30 50 ON or OFF * TINT is for NTSC system only. Blue background With the blue background function ON, the TV will Automatically turn blue when no signal is being received. [. . . ] Before calling service personnel, please check the following chart for a possible cause to the trouble you are experiencing. Symptoms No power, red indicator is not lit up Poor colour, poor tint Spots appear on the screen Stripes appear on the screen Check the following items Troubleshooting Guide . . Double images or "ghosts" Snowy picture The remote controller does not work . Even if the picture or the sound is normal, Be sure the power cord is plugged in. [. . . ]