User manual PANASONIC CQ-DP975EW
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual PANASONIC CQ-DP975EW. We hope that this PANASONIC CQ-DP975EW user guide will be useful to you.
Manual abstract: user guide PANASONIC CQ-DP975EW
Detailed instructions for use are in the User's Guide.
[. . . ] (Hours blink. )
(Default)
Volume level (0 to 40)
3 Press [% TUNE] or [$ TUNE].
(Hours set. ) Minutes 4 Press [DISP] (CLOCK). (Minutes blink. )
Pattern 1 Pattern off
Pattern 2
Pattern 3 Pattern 4
Treble:
Loudness
Press [LOUD] to enhance bass and treble tones at low or medium volume.
LOUD
Balance:
Adjustable range: j12 dB to i12 dB (by 3 dB step)
R (right speaker) or L (left speaker)
5 Press [% TUNE] or [$ TUNE].
(Minutes set. )
Press [LOUD] again to cancel.
Adjustable range: 1 to 15 (by 1 dB step)
Balance center
6 Press [DISP] (CLOCK).
(End. ) Note: Press and hold [% TUNE] or [$ TUNE] for more than 2 seconds to change numbers rapidly.
Fader:
Mute
Press [MUTE] to mute the sound completely.
MUTE
Anti-volume-blast circuit: When the power is switched off and on again, the volume slowly rises to the previous level. The anti-volume-blast circuit will not work when the volume level is set lower than position 20 on the display.
F (front speaker) or R (rear speaker)
Adjustable range: 1 to 15 (by 1 dB step)
Fader center
Time Reset
Press and hold [DISP] (CLOCK) for more than 2 seconds to activate the time setting mode to reset the time. CQ-DP975EW
Press [MUTE] again to cancel.
Note: If no operation takes place for more than 5 seconds in audio mode (2 seconds in volume mode), the display returns to the regular mode.
10
CQ-DP975EW
11
E N G L I S H 3
Radio Basics
1 Radio Mode change Press [SOURCE] to
to the radio mode.
Preset Station Setting
Source Radio CD player
(When a CD is inserted. ) Up to 6 stations each can be saved in the FM1, FM2, FM3 and AM preset station memories. [. . . ] Clean disc, referring to the section on "Notes on CD/CD Media (CDR, CD-RW)". The unit may not successfully play back a CD-R/RW that is made in combination of writing software, a CD recorder (CD-R/RW drive) and a disc which are incompatible one another. Do not write on the disc label in a heavy pen or ballpoint pen stroke. Rough edges
Label side
Note: There may be cases where the disc numbers affected by an error are designed before "E1" or "E2". Displays and the steps to be taken for errors vary in part from changer to chager. For details, refer to the operating instructions for the changer used.
Do not use irregular shaped discs. <Right> <Wrong>
Maintenance
Your product is designed and manufactured to ensure a minimum of maintenance. Never use benzine, thinner or other solvents.
Product Servicing
If the suggestions in the charts do not solve the problem, we recommend that you take it to your nearest authorized Panasonic service station. The product should be serviced only by a qualified technician.
Replace the Fuse
Use fuses of the same specified rating (15 A). Using different substitutes or fuses with higher ratings, or connecting the product directly without a fuse, could cause fire or damage to the stereo unit. If the replacement fuse fails, contact your nearest Panasonic service station for service.
Notes on CD-Rs/RWs
You may have trouble playing back some CD-R/RW discs recorded on CD recorders (CD-R/RW drives), either due to their recording characteristics or dirt, fingerprints, scratches, etc. Panasonic Servicenter List for Service Directory . . . Keep for future reference in case the product needs servicing. Installation Hardware. . . Needed for in-dash installation.
Turn the ignition on to the accessory position, and ground one lead of the test bulb to the chassis. Touch the other lead of the test bulb to each of the exposed wires from the cut radio connector plug. Touch one wire at a time until you find the outlet that causes the test bulb to light. If your car is not wired for an audio unit: Go to the fuse block and find the fuse port for radio (RADIO), accessory (ACC), or ignition (IGN).
Connect All Leads
Now that you have identified all the wires in the car, you are ready to begin connecting them to the stereo unit wires. The wiring diagram ( page 28) shows the proper connections and color coding of the leads. We strongly recommend that you test the unit before making a final installation. You can set the unit on the floor and make temporary connections to test the unit. Important: Connect the red power lead last, after you have made and insulated all other connections. Ground Connect the black ground lead of the power connector to the metal car chassis.
Required Tools
You'll need a screwdriver, a 1. 5 V AA battery, and the following: 12 V DC Electrical Side-cut Test bulb tape pliers
Overview
This product should be installed by a professional. However, if you plan to install this product yourself, your first step is to decide where to install it. [. . . ] The dashboard should be 4. 75 mmj5. 56 mm thick in order to be able to support the unit.
Final Installation
Lead Connections Connect all wires, making sure that each connection is insulated and secure. Bundle all loose wires and fasten them with tape so they will not fall down later. After making a few final checks, you're ready to enjoy your new auto stereo system.
3 mm· 2 Hex. nut (5 mm·) 3 Rear support strap 5 Mounting bolt (5 mm·) 1 Mounting collar
5 Mounting bolt (5 mm·) 1 Mounting collar
24
CQ-DP975EW
CQ-DP975EW
25
E N G L I S H 17
Installation Guide (Continued)
Remove the Unit
Switch off the power of the unit. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE PANASONIC CQ-DP975EW
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual PANASONIC CQ-DP975EW will begin.