User manual PANASONIC WV-CL920

[. . . ] Colour CCTV Cameras Operating Instructions WV -C CL R9 24 Model No. WV-CLR920 WV-CLR924 (Lens : option) Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. FRANÇAIS ENGLISH ENGLISH VERSION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN For U. K. FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY. WARNING: This apparatus must be earthed IMPORTANT The wires in this mains lead are coloured in accordance with the following code. Green-and-yellow: Earth Blue: Neutral Brown: Live As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows. The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol I or coloured green or green-and-yellow. The wire which is coloured blue must be connected to the terminal in the plug which is marked with the letter N or coloured black. [. . . ] * The GUI stands for Graphical User Interface. SETTING PROCEDURES 1. Camera Identification (CAMERA ID) Setting You can use the camera identification (CAMERA ID) to assign a name to the camera. The camera ID display can be switched on or off on the monitor screen. ** CAM SET UP ** CAMERA ID OFF ALC/ELC ALC SHUTTER OFF AGC ON (DNR-H) SENS UP OFF SYNC INT WHITE BAL ATW1 MOTION DET OFF LENS DRIVE DC RET Character Cursor 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ (). , '":;&#!?= +-*/%$ÄÜÖÆÑÅ SPACE POSI RET END RESET . . . . . . . . . . . . . . . . Character Area Command Editing Area Pointer CAMERA ID menu 3. (The pointer in the editing area moves to the right automatically at this moment. ) 5. To enter a blank space in the CAMERA ID Move the cursor to SPACE and press . Then move the cursor to the character area and select a new character. To erase all characters in the editing area Move the cursor to RESET and press . The display shown below appears and the CAMERA ID is highlighted. Highlighted 3. Notes: · The CAMERA ID stops at the edges of the monitor screen. · The CAMERA ID moves faster if any of / / / is kept pressed for a second or more. 2. Light Control Setting (ALC/ELC) You can select the mode for adjusting the lens iris. The modes are as follows: ALC: Select this mode when an auto iris lens (ALC lens) is used with this camera. ELC: Select this mode when a fixed iris lens or manual iris lens is used with this camera. ** CAM SET UP ** CAMERA ID OFF ALC/ELC ALC SHUTTER OFF AGC ON (DNR-H) SENS UP OFF SYNC INT WHITE BAL ATW1 MOTION DET OFF LENS DRIVE DC RET WV-CLR920 2. Move the CAMERA ID to the desired position by pressing / / / . -26- 1. Under bright lighting conditions such as outdoors, use an ALC type lens because the ELC control range is not wide enough under these conditions. Use an ALC type lens if the following phenomena occur: · Strong smear and/or blooming on highlight objects such as spotlight or sunlight from windows. · Noticeable flicker in the picture and/or colour rendition variations. Back Light Compensation (BACK LIGHT COMP) Back light compensation is available for both the ALC and ELC modes. It eliminates strong background lighting which makes the camera picture dark, such as a spotlight. You can select one of two modes (PRESET ON or PRESET OFF) of back light compensation. 2-1. ALC Mode with PRESET ON In normal use, the important object in a scene is placed in the centre of the monitor's screen. In the factory setup mode, more photometric weight is given to the centre of the screen (where the important object is located) than to the edge of the picture (where a bright backlight would most likely be located). [. . . ] Therefore, when the camera is not used in a Panasonic Intelligent CCTV System, select OFF to prevent the above from occurring. · To confirm the changed parameter of Alarm Data Setting on the RS485 Setup menu for DISPLAY MODE, move the cursor to RET to return to the previous menu and move the cursor to END to close the menu once. 9. Lens Drive Signal Selection (LENS DRIVE) This item is used to select the type of auto iris lens drive signal to be supplied to the lens from the auto iris lens connector. ** CAM SET UP ** CAMERA ID OFF ALC/ELC ALC SHUTTER OFF AGC ON (DNR-H) SENS UP OFF SYNC INT WHITE BAL ATW1 MOTION DET OFF LENS DRIVE DC RET 1. Select DC if you are using the auto iris lens that requires a DC drive signal. [. . . ]