User manual PHILIPS 220V1SB

[. . . ] Philips LCD Monitor Electronic User's Manual · Safety Precautions and Maintenance · FAQs · Troubleshooting · Regulatory Information · Other Related Information Safety and Troubleshooting Information Safety precautions and maintenance WARNING: Use of controls, adjustments or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards and/or mechanical hazards. Read and follow these instructions when connecting and using your computer monitor: Operation: %Ï %Ï %Ï %Ï %Ï %Ï %Ï %Ï Keep the monitor out of direct sunlight and away from stoves or any other heat source. Remove any object that could fall into ventilation holes or prevent proper cooling of the monitor's electronics. When positioning the monitor, make sure the power plug and outlet are easily accessible. If turning off the monitor by detaching the power cable or DC power cord, wait for 6 seconds before attaching the power cable or DC power cord for normal operation. [. . . ] 4 . Select the 'Settings' tab then click on 'Advanced. . . '. 5 . Select the 'Monitor' button, point to 'Change. . . ' then click on 'Have Disk. . . '. 6 . Click on the 'Browse. . . ' button, select the appropriate drive F: ( CD-ROM Drive) then click on the 'OK' button. 7 . Click on the 'OK' button then select your monitor model and click on 'OK'. 8 . Click on the 'Close' button. For Windows® 98 1Start Windows® 98 . 2 . Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'. 4 . Select the 'Settings' tab then click on 'Advanced. . . '. 5 . Select the 'Monitor' button, point to 'Change. . . ' then click on 'Next' 6 . Select 'Display a list of all the drivers in a specific location, so you can choose the driver you want. ' then click 7 . Click on the 'Browse. . . ' button, select the appropriate drive F: ( CD-ROM Drive) then click on the 'OK' button. 8 . Click on the 'OK' button then select your monitor model and click on the 'Next' button. 9 . Click on the 'Finish' button then the 'Close' button. For Windows® 2000 on 'Next' and then click on 'Have Disk. . . '. 1Start Windows® 2000 . 2 . Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'. 4 . Select the 'Settings' tab then click on 'Advanced. . . '. Select 'Monitor' - If the 'Properties' button is inactive, it means your monitor is properly configured. 6 . Click on 'Driver' and then click on 'Update Driver. . . ' then click on the 'Next' button. 7 . Select 'Display a list of the known drivers for this device so that I can choose a specific driver', then click on 'Next' and then click on 'Have disk. . . '. 8 . Click on the 'Browse. . . ' button then select the appropriate drive F: ( CD-ROM Drive). 9 . Click on the 'Open' button, then click on the 'OK' button. 1 0 Select your monitor model and click on the 'Next' button. 1 1 Click on the 'Finish' button then the 'Close' button. If you can see the 'Digital Signature Not Found' window, click on the 'Yes' button. 2 . Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'. 4 . Select the 'Settings' tab then click on 'Advanced. . . '. 5 . Select the 'Monitor' button, then click on 'Change. . . ' button. [. . . ] Each hub converts a single attachment point into multiple attachment points. Each of the other downstream ports of a hub allows connection to another hub or function. Hubs can detect, attach and detach at each downstream port and enable the distribution of power to downstream devices. Each downstream port can be individually enabled and configured at either full or low speed. [. . . ]