User manual PLEXTOR 482448U

[. . . ] Model PX-W4824TU (External) INSTALLATION AND USERS MANUAL SEPTEMBER 2002 Plextor reserves the right to make improvements in the products described in this manual at any time without prior notice. Plextor makes no representation or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. reserves the right to revise this manual and to make changes in its content without obligation to notify any person or organization of such revision or change. It may not be copied, photocopied, translated, or reduced to any electronic medium or machine-readable form without Plextor's prior permission. Manual copyright ©2002 Plextor Corp. [. . . ] See "Recommended Media on page 23 for a list of Plextor-approved media at the time this manual was printed, and see the Plextor web site at http://www. plextor. com for an updated list. You can write to Ultra Speed RW discs only on drives that support this new media. Drives that are capable of writing to Ultra Speed RW media, such as the PlexWriter 48/24/48U, are identified by a "Compact Disc ReWritable Ultra Speed" logo. Install Device Drivers (Windows 98SE Only) In Windows, your PlexWriter acts as a "CD-ROM Drive" for purposes of installation and setup. In some cases, you will need to install additional software to make use of all of the features of the PlexWriter. As CD-ROM: The computer's operating system, whether it is Windows XP, Windows 2000, or Windows Me, supplies a generic USB device driver that allows the PlexWriter to function as a standard CD-ROM drive. You'll find this driver on the Plextor Setup Disc, or you can get it from the Plextor web site at http://www. plextor. com. (Follow the links from the home page to Support\Downloads\Drivers. ) PlexWriter 48/24/48U Installation and Users Manual 13 Section 3. As a CD-R or CD-RW device: In order to write to CD-R or CD-RW media, you will need additional software such as SimpliCD® or Easy CD CreatorTM . Whether using the PlexWriter as a standard CD-ROM or as a CD-R or CD-RW device, you will need additional drivers or software besides those that are part of the Macintosh operating system. The software compatibility list is available from Plextor's web site at www. plextor. com. Before installing any software, check that the USB cable connection between your PlexWriter and the computer is correct, and the PlexWriter is recognized by your system. Tray Loading and Operation To load and unload the tray: 1. While the PlexWriter drive is powered up, push the eject button on the front panel. The tray drawer slides out in 3­4 seconds. Figure 5: Loading the Tray 2. Press the eject button again and the tray will slide shut within seconds. NOTE: Always use the eject button to close the tray in a smooth and secure manner. Closing the tray by pressing the front of the drawer by hand is not recommended and risks damage or premature wearing of the mechanism and your CDs. Handling CD Media Take care when handling blank CD-R and CD-RW media. Dust, scratches, and fingerprints on either side of the disc can cause write errors during recording. When picking up or holding blank media you can either place your fingers along the outer edge of the disc, or place one finger through the center hole and one finger on the outer edge. Once you have finished creating a disc, label it by writing on the top using permanent ink. Using Your PlexWriter CAUTION: We recommend using a "non-toxic" marker, such as a Sharpie?Also, do not press too hard when writing on the disc. Cleaning Discs For proper read and write performance, your CD-R, CD-RW, and CD-ROM discs must be clean. Trying to record on a dirty disc may result in a failed session and ruin the disc. To clean the disc, wipe the disc using a clean, soft cotton cloth to remove surface dirt such as fingerprints. [. . . ] Fill out the RMA Request Form, include the Tech Support Ticket Number, and e-mail or fax the form to Plextor to request an RMA number. Plextor then sends you the RMA form with the RMA number and shipping information included. When you receive the RMA number, pack the Plextor drive securely in a box, and include the RMA form as a packing slip. Write the RMA number in large letters on the outside of the box, and ship it to Plextor. Contacting Plextor's RMA Department You can contact our RMA Department and request RMA forms at: ?? [. . . ]