Detailed instructions for use are in the User's Guide.
[. . . ] WARNING: Always disconnect spark plug wire and place it where it cannot contact plug in order to prevent accidental starting when setting up, transporting, adjusting or making repairs. WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Do not use snow thrower on surfaces above ground level such as roofs of residences, garages, porches or other such structures or buildings. WARNING: Snow throwers have exposed rotating parts, which can cause severe injury from contact, or from material thrown from the discharge chute. [. . . ] To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.
CHOKE CONTROL THROTTLE PRIMER ENGINE OIL FILL CAP / DIPSTICK
SCRAPER BAR The scraper bar is not adjustable, but is reversible. When it has worn almost to the edge of the housing, it can be reversed, providing additional service before requiring replacement. 20) Use the drift cutters to cut through deep snowdrifts that are higher than the front of the snow thrower. · Loosen upper adjustment nut enough to allow drift cutter to be raised to highest position and tighten nut securely. · When not using drift cutters, loosen adjustment nut, lower to storage position and tighten nut securely.
AUGER HOUSING STORAGE POSITION DRIFT CUTTER
SAFETY IGNITION KEY
GASOLINE FILLER CAP FUEL SHUTOFF VALVE RECOIL STARTER HANDLE STARTER BUTTON POWER CORD PLUG
ADJUSTMENT NUT FIG. 21
12
OPERATION
TO START ENGINE · Be sure fuel shut-off valve is in the "OPEN" position. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A. C. WARNING: Do not use the electric starter if your house is not a 120 Volt A. C. Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks. After snow-throwing is completed, allow engine to run for a few minutes to melt snow and ice off the engine. Clean the entire snow thrower thoroughly after each use and wipe dry so it is ready for next use. WARNING: Do not operate snow thrower if weather conditions impair visibility. Throwing snow during a heavy, windy snowstorm can blind you and be hazardous to the safe operation of the snow thrower.
MAINTENANCE
GENERAL RECOMMENDATIONS
The warranty on this snow thrower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain snow thrower as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your snow thrower. All adjustments in the Service and Adjustments section of this manual should be checked at least once each season. · Once a year, you should replace the spark plug and check belts for wear. NOTE: Use only Original Equipment Manufacturer (OEM) parts to service this unit. Failure to do so can cause the unit to malfunction and pose a risk of injury to the operator.
LUBRICATION CHART
SAE 5W-30 Motor Oil See "ENGINE" in Maintenance section General Purpose Grease
Pivot points
BEFORE EACH USE
1. Check controls to be sure they are functioning properly.
LUBRICATION
Keep your snow thrower well lubricated (See "LUBRICATION CHART"). [. . . ] Failure to do so could be hazardous, damage your snow thrower and void your warranty. 27
REPAIR PARTS SNOW THROWER - MODEL PP11530ES (96192001900) CHASSIS / ENGINE / PULLEYS
30
3 53
58
19
17
57 6 22 23
28
6
10 21
5 31 29 56
4 10 21
24 25 18 20 26 27
31 32 36 32 37 11 36 44 43 33 34 35 11 45 41 39 50 11 8 38 5 16 1
5
26 42 9 12 7 13 14 15
44
52 49 47
5 51 40 46
28
REPAIR PARTS SNOW THROWER - MODEL PP11530ES (96192001900) CHASSIS / ENGINE / PULLEYS
KEY PART NO. 1 2 3 414557 180522 ---
DESCRIPTION Spring, Traction Idler Pulley, Idler (2-1/4) Engine, Tecumseh, Model Number LH358SA (For engine service and replacement parts, call Tecumseh Products at 1-800-558-5402) Screw, Hex Head 5/16-18 x 1-1/4 Screw Washer, Flat Nut, Jam, Lock 5/16-18 Pin, Idler Pivot V-Belt, Traction Drive Washer, Lock 5/16 Screw, Hex Washer Head 5/16-18 x 1/2 Impeller Arm Assembly Retainer, Hairpin Spring, Brake V-Belt, Impeller Drive Screw, Hex Head 3/8-16 x 1-1/4 Arm, Idler Screw, Hex Head 5/16-18 x 1-1/2 Bushing, Idler Pivot Pulley, Idler (2-3/4) Screw, Hex Head 5/16-24 x 1 Spacer, Engine Pulley Pulley, Engine, Traction Drive Pulley, Engine, Impeller Drive Washer, Flat 3/8 Washer, Lock 3/8
KEY PART NO. 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 49 50 51 52 53 56 57 58 851084 155452 192213 178830 17490408 402881 403096X004 198580 405485 191730 402856X004 187101 402857X004 413429 700279 73930500 403097X004 17000616 175324X479 410877 184471 409345X428 402685X428 406109 57079 35062 417014X428 11050500 198563
DESCRIPTION Screw, Hex Head 3/8-24 x 1-3/8 Guide, Belt Belt Cover Assembly (Includes Toolbox Cover) Cover, Toolbox Screw, Hex Head 1/4-20 x 1/2 Bolt, Shoulder 5/16-18 Bellcrank Shifter Clevis Pin Arm, Auger Control Locknut, Hex Plate, Clutch Link, Speed Control Bracket, Clutch Bracket, Traction Hairpin, Cotter 3/32 x 1/2 Locknut, Hex Plate, Shifter Screw, Hex Head Pivot Bracket, Impeller Idler Arm Pan, Frame Bottom Screw Frame Assembly Plate, Frame End Shaft, Auger Control Washer, Hardened Key, Safety Mounting Plate, Engine Washer, Lock, External Tooth Power Cord
4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
74780520 150078 59289 166785 175330 407908 10040500 17490508 410420 85179 178828 408007 150406 187786 74780524 175331 180523 74610516 409475 180478 179157 400026 850263
NOTE: All component dimensions given in U. S. [. . . ]