User manual PROGRESS PAI8000E

[. . . ] General safety · The appliance may only be installed and connected by trained, registered service engineers. · Built-in appliances may only be used after they have built in to suitable built-in units and work surfaces that meet standards. · In the event of faults with the appliance or damage to the glass ceramic (cracks, scratches or splits), the appliance must be switched off and disconnected from the electrical supply, to prevent the possibility of an electric shock. · Repairs to the appliance must only be carried out by trained registered service engineers. [. . . ] Control panel Switch on the appliance Touch Touch until the signal sounds Acoustic signal Display/Signal Appliance switches off. The child safety device is released. Switching the power function on and off makes additional The power function power available to the front induction cooking zones, e. g. The power function is activated Control panel Switch on Switch off Touch Touch Touch for 8 minutes for the front left cooking zone and for 5 minutes for the front right cooking zone. After these times, the induction cooking zones automatically return to cooking level . Display If the power function has ended, the cooking zones automatically switch back to the heat setting set previously. progress 7 Power Management The cooking zones of the cooking surface have a maximum power available to them. So that the Power function can always be carried out, Power Management may reduce the power of the other cooking zone in the pair Example: heat setting 9 is selected on a cooking zone. The Power function is switched on for the cooking zone paired up with it. The Power function is performed, but heat setting 9 on one cooking zone and Power function on the other cooking zone of a pair exceeds the maximum output for both. Therefore Power Management reduces the first cooking zone that was switched on from 9 to 7, for example, and the display for this cooking zone alternates between 9 and 7 and then remains on the current maximum of Using the timer All cooking zones can use each use one of the two timer functions at the same time. Function Automatic cut-out Countdown timer Condition a heat setting is set cooking zones not in use Outcome after the time has elapsed acoustic signal 00 flashes Cooking zone switches off acoustic signal 00 flashes 7. (Whether the display alternates between 9 and 7 or 9 and 6 or other values, depends on the appliance type and the size of the cooking zone. ) If a cooking zone is switched off, the timer function set is also switched off. If a heat setting is set on this cooking zone in addition to a countdown timer, Selecting a cooking zone Ste p 1. Control panel Touch once Touch once Touch once Touch once the cooking zone is switched off after the time set has elapsed. Display Pilot light of the first cooking zone flashes Pilot light of the second cooking zone flashes Pilot light of the third cooking zone flashes Pilot light of the fourth cooking zone flashes 8 progress The heat setting indicator of the selected cooking zone goes out, as long as the timer time can be set. If the pilot light is flashing more slowly, the heat setting indicator appears again and the heat setting can be re-set or modified. Control panel Selecting cooking zone Touch zone or from the selected cooking If other timer functions are set, after a few seconds the shortest remaining time of all the timer functions is displayed and the corresponding pilot light flashes. Grill seting Telltale of cooking zone selected flashes 01 to 99 minutes After a few seconds the power indicator flashes more slowly. Control panel Select a cooking zone Display Pilot light of the selected cooking zone flashes more quickly. Remaining time is displayed The remaining time counts down to 00. 2. Touch for the cooking zone selected or from the Simultaneously Touch selected cooking zone 00 is displayed. The pilot light goes out. The Timer function for the selected cooking zone is switched off. Changing the time Step 1. Control panel field Select cooking zone Touch or selected for the cooking zone Display Pilot light of the cooking zone selected flashes faster The time remaining is displayed 01 to 99 minutes After a few seconds the pilot light flashes more slowly. The time counts down. Displaying the time remaining for a cooking zone Step 1. Control panel field Select cooking zone Display Pilot light of the cooking zone selected flashes faster The time remaining is displayed After a few seconds the pilot light flashes more slowly. Switching off the acoustic signal Step 1. Suitability test Cookware is suitable for induction cooking, if . . . · . . . a little water on an induction cooking zone set to heat setting 9 is heated within a short time. a magnet sticks to the bottom of the cookware. 10 progress Certain cookware can make noises when being used on induction cooking zones. [. . . ] · Have the clamping connections correctly installed by a qualified electrician. · Use strain relief clamp on cable. · In the event of single-phase or twophase connection, the appropriate mains cable of type H05BB-F Tmax 90°C (or higher) must be used. · If this appliance's mains cable is damaged, it must be replaced by a special cable (type H05BB-F Tmax 90°C; or higher). The latter is available from the Customer Care Department A device must be provided in the electrical installation which allows the appliance to be disconnected from the mains at all poles with a contact opening width of at least 3 mm. [. . . ]