User manual QSC AUDIO NAC-100

[. . . ] 1675 MacArthur Blvd. , Costa Mesa, CA 92626 USA Main Number (714) 743-6175 or toll free (800) 854-4079 Customer Service (714) 957-7250 or toll free (800) 772-2834 NAC-100 Network Audio Controller User Manual NAC-100-BK NAC-100-WH TD-000270-00 rev. A The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous" voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to humans. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in this manual. This unit has been engineered and manufactured to assure your personal safety. Improper use can result in potential electrical shock or fire hazards. [. . . ] To enter the UTILITY SELECT MENU, press and hold the Rotary Button, then simultaneously press the Blue Button. (The default password is qsc. ) Turn the Rotary to select individual letters in the password. (The password should be completely represented by the "*" symbol before pressing the Blue Key, e. g. "***". ) A letter may not be changed after it has been entered. If an error is made, press the Blue Key to begin entering the password from the beginning. NETWORK SETUP UTILITY IP Address: __. __. __. __ Subnet Mask: __. __. __. __ UTILITY SELECT MENU Network Setup Security Access LCD Contrast Adjust Basis Connection Status System Information Reboot/Restart Restore Factory Default SYSTEM INFORMATION NAC-100 Name: Firmware Version: Serial Number: SECURITY ACCESS All Control Items Unlocked REBOOT / RESTART System will now reboot. . . CONTRAST ADJUST Contrast: RESTORE DEFAULT -- Caution!!-- This will erase all screens and bitmaps, replaced with Factory default memory settings. Press Blue Button To Start BASIS CONNECT STATUS Basis Index: IP Address: Status: Name: Model: Utility Select Menu Descriptions TOP MENU UTILITY SELECT MENU Network Setup Security Access LCD Contrast Adjust Basis Connection Status System Information Reboot/Restart Restore Factory Default SUB MENUS NETWORK SETUP UTILITY (Read/Write) IP Address: The NAC-100 IP Address Subnet Mask: The NAC-100 Subnet Mask SECURITY ACCESS All Control Items Unlocked -orPress Blue Key To Disable Security All Control Items Unlocked -orPress Blue Key To Re-enable Security All Control Items Locked CONTRAST ADJUST Contrast: BASIS CONNECT STATUS (Read Only) Basis Index: IP Address: Status: Name: Model: SYSTEM INFORMATION (Read Only) NAC-100 Name: Firmware Version: Serial Number: REBOOT / RESTART System will now reboot. . . RESTORE DEFAULT --Caution!!-This will erase all screens and bitmaps, replaced with factory default memory settings Press Blue Button to Start The default screen if none of the user configured Control Items are restricted using the Control Password. This option disables Control Password restrictions for all Control Items. Use this sub menu to check the status of any Basis unit controlled by the NAC-100. Restores factory defaults and restarts the NAC-100. Control Password restrictions have been disabled for all Control Items. This screen appears if user access passwords have been previously disabled. This option will re-enable Control Password restrictions for all Control Items. Control Password restrictions have been re-enabled for all Control Items. Range of 1-10, with 10 being the brightest. Basis Index ­ Change this number to view each of the Basis units controlled by the NAC-100. Basis IP Address Connection Status Basis Name Basis Model The name of the NAC-100 Current Firmware Version Serial Number Passwords There are two passwords on the NAC-100, one for Utility Select Menu, and one for Control Items. Note that a "crossover" data communications cable may be required depending on the port properties of the PC and/or ILP in use. NAC-100 D C AA DP ILP NAC-100 product is powered from an IEEE 802. 3af compliant inline power (ILP) source. The ILP combines DC power and data onto a single CAT-5e cable, which is connected to the NAC-100. BASIS Processor Figure 6: Single NAC-100 powered via IEEE 802. 3af compliant ILP (power injection source). This type of connection scheme is useful for managing very small systems with an NAC-100 when networked audio transport (CobraNet) is not required. Note that a "crossover" data communications cable may be required depending on the port properties of the ILP in use. Getting Started This section outlines one of the simpler methods of getting familiar with NAC-100 and the QSControl. net Venue Manager software. The goal of this procedure is to get your computer and the NAC-100 connected and communicating and the Venue Manager software installed and running. After the software is installed and running, refer to the Venue Manager's help file for all software related operation/issues. Note: The default password for the NAC-100 is "qsc" (no quotes, lower case). 2- Use one of the Network Diagrams illustrated previously in this manual to connect the NAC-100 to the network. [. . . ] All software operation is covered in the on-line help file. Operation of the NAC-100 is accomplished with the included QSControl. net Venue Manager software. After installing your software, open the Help file and follow its recommendations. The software Help file includes the most recent information available for your NAC-100. Resetting the NAC-100 Resetting the NAC-100 should only be performed as a last resort. -Remove the cover of NAC-100 to access the RJ45 jack, located on the circuit board of the NAC-100. [. . . ]