User manual RICOH FW 870
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual RICOH FW 870. We hope that this RICOH FW 870 user guide will be useful to you.
You may also download the following manuals related to this product:
RICOH FW 870 (1281 ko)
Manual abstract: user guide RICOH FW 870
Detailed instructions for use are in the User's Guide.
[. . . ] ,
I In accordance
I
for the main switch:
with ISO Standard 7001, this machine uses the following-- symbols
0
Q)
I
means POWER ON. I
I For good copy quality, Ricoh recommends
Ricoh shall not be responsible for any damage or expense that may result from the use of parts other than genuine Ricoh parts in your Ricoh office product. I Note:
Some illustrations may be slightly different from your machine. 1
115 V, 60 HZ, 12A Power Source: Please make sure to connect the power cord to a power source as above. [. . . ] 1 Press the Paper Select key until
your desired paper feeder indicator blinks. When
you select "Manual Feed" for the paper feeder, you cannot specify the paper size. 4 To use the New-ABCDE-size
paper, select "New size" using the + and - keys. When
the paper feeder indicator blinks for "New size", the 24, 18, 12, and 9 indicators are lit. 22 COPYING
PAPER TYPE/ROLL WIDTH ENTRY FUNCTION
5 Press the Fusing Temperature
key to select the paper type. If you do not want to store the
settings, press the Clear Modes key. COPYING 23
USING THE PROGRAM FUNCTION
The Program function allows you to store a collection of copy settings as programs 1 to 9 and switch them as needed. 2 Use the
and keys to select a program number for which you store copy settings. Each time you make a copy, the copy settings are stored in Program No. 24 COPYING
USING THE PROGRAM FUNCTION
4 Specify values for each setting. When you specify a paper feeder, the paper type and roll width specified with the Paper Type/Roll Width Entry function (see page 22) are stored. The settings are also stored
when you press the Program key instead of the Enter key. cOPYING 25
USING THE PROGRAM FUNCTION
Recalling Programmed Settings
1 Press the Program key. When you press the Program
key again, you can cancel the program recall. 26 COPYING
COPYING WITH MANUAL FEED
When you make a copy with manual feed, you need not replace paper even if the required size or type of paper is not set in the copier. S You cannot use the repeated copying function during manual copying in the default setting. When you have set both of them, the copier starts copying automatically. S When you press the Clear/Stop key after setting an original, the original is delivered without copying. S When you remove paper from the manual feed table, pull it out gently by holding its left and right sides. COPYING 27
COPYING WITH MANUAL FEED
3 Set the copy paper guide to match
the paper width and direction (the copy paper guide is an option). 4 Insert the paper lightly along the
copy paper guide (the copy paper guide is an option). 43
WHEN THE "WAIT" INDICATOR IS LIT
You cannot start copying while the "Wait" indicator is lit. [. . . ] In particular, when you use the humidifier continuously for a long time, a humidifier demineralizer is recommended. The copier must be level within 5 mm both front to rear and left to right. If the copier is not stabilized, it might cause a fault as well as a danger to users. S To avoid a possible build-up of ozone, make sure to locate this copier in a large well ventilated room that has air turnover of more than 30m3/hr/person. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE RICOH FW 870
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual RICOH FW 870 will begin.