User manual SCHWINN 17 FUNCTION BIKE COMPUTER

[. . . ] Speed Tendency: A cyclist symbol appears to the left of the speed display. To switch between the two formats, press left button and hold for a few seconds until the bottom line flashes either 12 or 24 (depending on current format). Press right button to move to the next screen. 3rd Screen - Tripmeter (DST) Speedometer: Displayed on top line. [. . . ] To reset ODO to zero, press and hold both buttons for a few seconds until the screen changes or remove the battery. Press right button to move to next screen. 9th Screen - Fat Burning (CALF ) Speedometer: Displayed on top line. Press right button to move to Scan mode. Scan In Scan mode, the screen cycles through DS7", MXS, AVS, and TM modes. Press right button to return to Speedometer mode. Troubleshooting Malfunction No speedometer reading Remedy Check alignment of magnet & sensor. Verify temperature is within operating limits 1 30 ) Replace battery Reseat battery Replace battery Reseat battery Replace battery Check alignment of magnet & sensor. Reseat battery Replace battery Reseat battery Replace battery Slow display response Black Display Freeze Frame Memory Press the left button, Freeze Frame Memory can lock the display at the end of a ride segment. TM, DST, and AVS, which will be flashing, can be read at a later time by pressing the right key. To reset the memory, press the left button; the display will stop flashing. This is particularly useful when crossing the finish line of a time trial. Note: Computer must be in either ODO, DST; MXS, AVS, or TM mode for this function to work. Display readout fades No trip distance readout Display shows irregular figures PACIFICCYCLE Odometer Reset Function The Odometer Reset Function allows you to reenter your total distance after the odometer has been reset to zero. In the ODO mode, press the left button for a few seconds until the last digit flashes. After selection of last digit, computer will return to ODO mode. 4902 HAMMERSLEY ROAD MADISON, Wl 53711 www. pacific-cycle. com For customer service inquiries: Toll Free: (800)515-0074 customerservice@pacific-cycle. com Made in China www. schwinnbike. com ©2008 Pacific Cycle Inc. 17 Functions Art No: SU17-EL-P3-GB-SCHWINN-R6 Features 17 FUNCTIONS Speedometer (0 - 99. 9 M/hr or KM/tir) (accuracy of +/- 0. 5 M/hr or KM/hr) Tripmeter (Up to 99. 9 M or KM) Odometer (Up to 9999. 9 M or KM) Trip Timer (9:59'59") Maximum Speed (Up to 99. 9 M or KM) Digital Clock (12/24 hour selectable) Average Speed (Up to 99. 9 M or KM) Scan (DST MXS, AVS, TM) Freeze Frame Memory (TM and AVS) Speed Comparator (+ or -) ( Speed Tendency Odometer Reset-Function Maintenance Program Step Counter (In pedometer mode) Calorie Counter (0. 0 to 9999 Calories) Fat Burned (0. 0 to 9999 Grams) Temperature EL Backlight C to ) / (14T - 122T) Quick Set-up 1. Miles/Kilometer per Hour Press right button to switch between kilometers and miles. Press left button to select. Battery Installation Remove the battery cover from the bottom of the computer using a coin. Install the battery (3V/ CR2032) with the positive (+) pole facing the battery cover. 1). Speedometer Sensor & Magnet Clamp the magnet onto a spoke of the front wheel as shown (Fig. As the magnet passes the sensor, it should come within 1 mm of the sensor, but not touch the sensor (Fig. Maintenance Press right button to choose between 200, 400, 600 or 800 miles. [. . . ] To input wheel factor into the computer, press the right button to progress the digit and press the left button to select the digit (hold the right button for fast advance). (Note: removing the battery will erase wheel size. ) For your convenience, you may refer to the wheel chart below for your correct wheel factor. Auto Start / Stop To preserve batteries, the cycle computer will automatically switch off if the unit is left unused for over 5 minutes. Display will reappear with a press on either button or input from the sensor. Distance traveled in millimeters with one wheel revolution Fig. [. . . ]