User manual SHARP UX-A255
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SHARP UX-A255. We hope that this SHARP UX-A255 user guide will be useful to you.
Manual abstract: user guide SHARP UX-A255
Detailed instructions for use are in the User's Guide.
[. . . ] If you are not sure how to do this, get help from a qualified electrician.
IMPORTANT
The wires in this mains lead are coloured in accordance with the following code: GREEN-AND-YELLOW: Earth BLUE: Neutral BROWN: Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E, or by the safety earth symbol or coloured green or green-and-yellow. The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured red. This apparatus must be protected by a 13A fuse in the mains plug or distribution board.
"WARNING: THIS APPARATUS MUST BE EARTHED"
This equipment complies with the requirements of Directive 1999/5/EC. Dieses Gerät entspricht den Anforderungen der EU-Richtlinie 1999/5/EG. Quest'apparecchio è conforme ai requisiti delle direttiva 1999/5/CE. [. . . ] Sending Faxes
Loading one page at a time:
Loading up to 10 pages at once:
Loading the Document
Other restrictions
The scanner cannot recognise yellow, greenish yellow, or light blue ink. Ink, glue, and correcting fluid on documents must be dry before they pass
through the document feeder.
All clips, staples, and pins must be removed from documents before loading
in the feeder. If these are not removed, they may damage the machine.
Documents which are patched, taped, torn, smaller than the minimum size,
carbon backed, easily smudged, or have a slippery coated surface should be photocopied, and the copy loaded in the feeder.
Loading the Document
Up to 10 pages can be placed in the feeder at one time. The pages will automatically feed into the machine starting from the bottom page.
If you need to send or copy more than 10 pages, place the additional pages
gently and carefully in the feeder just before the last page is scanned. Do not try to force them in, as this may cause double-feeding or jamming.
If your document consists of several large or thick pages which must be
loaded one at a time, insert each page into the feeder as the previous page is being scanned. Insert gently to prevent double-feeding.
1
Adjust the document guides to the width of your document.
2
Insert the document face down in the document feeder. The top edge of the document should enter the feeder first.
· READY TO SEND will appear in the
display.
44
Adjusting the Resolution and Contrast
3
Adjust the resolution and/or contrast settings as explained in Resolution and Contrast below, then dial the receiving machine as explained on page 47.
Adjusting the Resolution and Contrast
If desired, you can adjust the resolution and contrast before sending a document.
The default resolution setting is STANDARD and the default contrast setting
is AUTO.
You must adjust the settings each time you don't want to use the default
settings.
Note: The resolution and contrast settings are only effective for sending a document. They are not effective for receiving a document.
Resolution settings
STANDARD Use STANDARD for ordinary documents. Use SUPER FINE for documents containing very small letters or very fine drawings. The original will be reproduced in 64 shades of gray.
FINE SUPER FINE HALF TONE
45
3. Sending Faxes
Adjusting the Resolution and Contrast
Contrast settings
AUTO DARK Use AUTO for normal documents. Dialling and transmission
If you are making a phone call, lift the handset. Dialling begins.
52
Sending a Fax by Automatic Dialling
Sending a fax by Direct Keypad Dialling
You can also enter a full number with the number keys and then press the
START/MEMORY
key to begin dialling. You can use this method to dial a full number
when you don't need to speak to the other party before faxing.
1
Load the document(s).
· If desired, press
RESOLUTION/ RECEPTION MODE
to set the
resolution and/or contrast.
READY TO SEND
2
Enter the number of the receiving machine by pressing the number keys.
· If a pause is required between any of the digits to access a special service
or an outside line, press
FUNCTION .
The pause will appear as a hyphen.
Several pauses can be entered in a row.
· If you are on a Flash-type PBX and are dialing out, press
R
, press
FUNCTION
to insert a pause, and then enter the number of the receiving machine.
· If you are on a PBX and must dial a number to dial out, enter the number,
press
FUNCTION
to insert a pause, and then enter the number of the receiving
machine.
3
Check the display. If the number of the receiving machine shown is correct, press
START/MEMORY
.
STOP
· If the number is not correct, press
to backspace and clear one digit
at a time, and then re-enter the correct digit(s).
53
3. Sending Faxes
Sending a Fax by Automatic Dialling
Redial
You can automatically redial the last number dialled. This procedure can be used to send a fax or make a phone call.
1
If you are sending a fax, load the document(s).
· If desired, press
RESOLUTION/ RECEPTION MODE
to set the
resolution and/or contrast.
READY TO SEND
2
Press once. <REDIAL> appears in the display, followed by the last number dialled. Make sure the number that appears is the number you wish to dial.
START/MEMORY
3
If you are sending a fax, press begins.
. Dialling and transmission
If you are making a phone call, lift the handset. Dialling begins.
Note: If a fax transmission is unsuccessful and DOCUMENT JAMMED appears in the display, remove the document as explained on page 90.
Automatic redialling
If you use automatic dialling (including Direct Keypad Dialling) to send a fax and the line is busy, the fax machine will automatically redial the number. The fax machine will make three redial attempts at an interval of five minutes. [. . . ] Troubleshooting
This appears if you attempt to send a fax by automatic dialling and the line is busy or the receiving fax machine does not answer. (See Automatic redialling on page 54. )
Clearing Paper Jams
Clearing Paper Jams
Clearing a jammed document
If the original document doesn't feed properly during transmission or copying, or DOCUMENT JAMMED appears in the display, first try pressing the document doesn't feed out, remove it as explained below. Important: Do not try to remove a jammed document without releasing it as explained below. If
1
Press and slowly open the operation panel until it is half open.
2
1
2
Flip up the green levers on each side of the white roller.
3
Gently remove the document.
· Be careful not to tear the document.
90
Clearing Paper Jams
4
Clearing jammed printing paper
1
Open the operation panel (press ).
2
1
2
Gently pull the jammed paper out of the machine, making sure no torn pieces of paper remain in the print compartment or rollers.
3
Rotate the front gear until the film is taut, and then close the operation panel (press down on both sides to make sure it clicks into place).
91
9. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SHARP UX-A255
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SHARP UX-A255 will begin.