User manual SIEMENS GIGASET A580 IP

[. . . ] The charging cradle and base station are designed for use in enclosed dry rooms with a temperature range of +5C to +45C. Do not use the phone in environments with a potential explosion hazard, e. g. Never expose the telephone to any of the following: heat sources, direct sunlight or other electrical appliances. Protect your Gigaset from moisture, dust, corrosive liquids and vapours. [. . . ] > The procedure below requires that your phone is automatically assigned an IP address by the 1 2 3 4 5 6 Preparing the handset: inserting the batteries Connecting the charging cradle to the mains power supply and charging the batteries Connecting the phone cord and power lead to the base station Connecting the base station to the fixed line network and the mains power supply To connect the base station to the Internet, first connect the base station to the router (connection via router and modem or via router with integrated modem) PC in LAN (optional) for advanced configuration of the Gigaset A580 IP base station > Do not put the handset back in the charging A cradle until the batteries are fully discharged through use. Keep the mains adapter plugged in at all times for operation, as the phone does not work without a mains connection. > After the first battery charge and discharge, you may place your handset in the charging cradle after every call. You can now use your phone to make calls via the fixed line network: Enter the number using the handset, and then press and hold the talk key c. router (i. e. if DHCP is not enabled on the router) you will have to assign a static IP address to the base station for LAN access. You must enter this IP address on the handset before carrying out the following steps. Further information can be found in the user guide on the enclosed CD. The following handset menu can be used to make the entry: Menu m Settings Base Local Network (enter system PIN) > The battery charging status is displayed in the idle display: = e V U (flat to full). > IP should be set as the default line for your phone (default setting). You will then immediately receive corresponding messages if a connection to the provider's VoIP server cannot be established due to incorrect/incomplete data. Saving VoIP access data 9 8 Saving VoIP access data Starting the connection assistant, entering the PIN Start VoIP connection wizard?No Yes System PIN: [____] 10 9 Saving VoIP access data Entering an auto-configuration code Code: 11 Saving VoIP access data 11 Entering VoIP account data 12 Instead of using the following procedure, you can also enter the VoIP access data using your PC (steps 7 to 11 ): > Enter your auto-configuration code using the keypad (max. > Enter the URL http://www. gigaset-config. com in the address field of the Web browser and press the return key. You can find a description of the Web configurator in the user guide on the enclosed CD. If your VoIP provider does not require a username, this step can be skipped. OK OK > Press the right-hand display key OK. All data necessary for VoIP telephony is loaded directly from the Internet to your phone. T OK > Using the number keys, enter your username (user ID) that you received from your VoIP provider. This entry is case-sensitive. > Press the right-hand display key OK. Precondition for the following steps: Before you can use VoIP to phone any other subscribers on the Internet, the fixed line network or the mobile phone network, you need a VoIP account. > Press the key below Yes on the display (= right display key). > Using the number keys, enter the base station's system PIN. By default, the PIN is "0000". 10 > To switch between upper and lower case and digits, press the # key (several times if nec- > Set up a VoIP account with a VoIP provider. > Have the VoIP account data you received from your VoIP provider to hand. > Press the right-hand display key OK. If the connection assistant does not start properly, you can start it via the menu: Menu m Settings Base Telephony Connection Assistant Selecting a provider and loading provider data to the base station Select provider is displayed briefly in the display. A list of providers is loaded and the first provider is shown in the display. essary). > Characters entered incorrectly can be deleted using the left display key X. The character to the left of the cursor will be deleted. You will need: > Your registration name (login ID), your password and, if applicable (provider-dependent), a user name (often this is your VoIP phone number). A list of countries is loaded and the first country in the list is shown in the display. > You can navigate within the input field using the control key p (press up/down). Provided that your phone is set for auto-configuration (default setting), you will see the following display. Germany Provider 1 OK Authentication Name: OK Authentication Password: V V > Your personal auto-configuration code (activation code), if your provider supports "automatic configuration". If you have received an autoconfiguration code: Do you have a code for auto configuration?No Yes T OK T OK 7 Starting the configuration process When your handset is sufficiently charged (approx. The first time you open the Gigaset. net directory, complete the following steps and an entry will be created in the Gigaset. net directory for you. Please note that, even with local calls, you must always dial the area code for calls via VoIP (provider-dependent). V You can now use your phone to make calls via the fixed line network and the Internet!Callers can contact you on your fixed line network number, your Gigaset. net number or your VoIP number! > Press down on the control key p to open the handset directory. [. . . ] We, Gigaset Communications GmbH, declare that this device meets the essential requirements and other relevant regulations laid down in Directive 1999/5/EC. A copy of the 1999/5/EC Declaration of Conformity is available at this Internet address: www. gigaset. com/docs. > Press the right-hand display key OK. If an entry already exists with this name, the message "Please choose another name. " will appear. If an entry in the Gigaset. net directory is successful, the message "Name added to Gigaset. net" will be shown. > Press the talk key c. > When prompted, speak into the microphone on the handset. If you hear your own voice, your base station is connected to the Internet. [. . . ]