User manual SIEMENS GIGASET S675

[. . . ] EN Dear Customer, Gigaset Communications GmbH is the legal successor to Siemens Home and Office Communication Devices GmbH & Co. Any statements made by Siemens AG or SHC that are found in the user guides should therefore be understood as statements of Gigaset Communications GmbH. Sehr geehrte Kundin, sehr geehrter Kunde, die Gigaset Communications GmbH ist Rechtsnachfolgerin der Siemens Home and Office Communication Devices GmbH & Co. KG (SHC), die ihrerseits das Gigaset-Geschft der Siemens AG fortfhrte. [. . . ] In this case you must also change the preset ID of the general mailbox ("0"). u You can only use personal mailboxes if your service provider supports this function. You can tell whether this is the case by the addition of a star (*) to the number of a (preset) SMS centre. u If you have forgotten your mailbox PIN, you can reset it by restoring the base station's default settings. This will delete all SMS messages from all mailboxes. Set Protection: to Off. The mailbox PIN is reset to "0000". v Settings SMS Mailboxes s (Select mailbox) Edit Press the display key. v Settings SMS Mailboxes s (Select mailbox) ~ Enter mailbox PIN if necessary and press OK. Set ID:, Protection: and PIN (page 32). Deactivating PIN protection Changing the name of a mailbox Changing a mailbox's PIN and ID Setting up and changing a personal mailbox v Settings SMS Mailboxes s Select mailbox, e. g. 32 Setting up a personal mailbox Sending an SMS to a personal mailbox To send an SMS to a personal mailbox, the sender must know your ID and enter it after your number. Your SMS contact will receive your SMS number with current ID and can save it in their directory. If the ID is invalid, the SMS will not be delivered. SMS (text messages) Setting SMS centres Entering/changing SMS centres SMS on a PABX Calling Line Identification is forwarded to the extension of the PABX (CLIP). The CLIP evaluation of the number of the SMS centre happens in your Gigaset. u If required, you must prefix the number for the SMS centre with the access code (depending on your PABX). by sending an SMS to your own number: once with and once without the access code. u When you send SMS messages, your sender number may be sent without your extension number. Sending and receiving SMS messages on ISDN PABXs is only possible via the MSN number assigned to your base station. u You can only receive an SMS when the and special functions offered by your service provider before you make a new application and/or before you delete pre-configured call numbers. Change multiple line input: Active Send: Select Yes if SMS messages are to be sent via the SMS centre. Enter the number of the SMS service and insert a star if your service provider supports personal mailboxes. Save changes (page 63). You should find out about the services Activating/deactivating muting for the first ringer tone v Open menu. Q OK Or: OK First ring muted. Please note: Ask your service provider for details on how to enter service numbers if you wish to use personal mailboxes (precondition: your service provider supports this function). Sending an SMS through another SMS centre Activate the SMS centre (2 to 4) as the This setting only applies to the next SMS to be sent. 1. Activating/deactivating the SMS function If you deactivate the SMS function, you cannot send or receive any SMS messages with your phone. The settings which you have made for sending and receiving SMS messages (e. g. the call numbers of the SMS centres) and the entries in the incoming and draft message lists are saved even after you turn off your phone. [. . . ] Select contrast and press the display key Save. r Press on the right or left of the control 62 key to set the contrast. Press the display key Save to confirm the selection. Notes on the user guide a Press and hold the end call key until the handset returns to idle status. Press and hold (idle status). Save the changes. Then press and hold the a key. The handset switches to idle status. Example of multiple line input In many situations you can change settings or enter data in several lines of a display. In this user guide icons are used to guide you step by step through multiple line input. [. . . ]