User manual SITECOM WIRELESS INTERNET SECURITY CAMERA 150N WL-405

[. . . ] Wireless Network IP-Camera 150N WL-405 Full Manual Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] You can access this menu by clicking `Log' on the top of web management interface. 3. 4 Video Setup You can specify the video and audio parameters of this IP camera here. 3. 4. 1 Dual Mode This IP camera supports two video encoding formats: MPEG4 and MJPEG. You can select the encoding format from one of them. The descriptions of every setting in this menu will be given below: Item Description Video Mode Specify default video encoding format of this IP camera here. Click `Apply' to save settings and make the new settings take effect. 3. 4. 2 MPEG4 If you selected `MPEG4' as the video encoding format of this IP camera, you can specify the parameters of the MPEG4 video encoder here. The descriptions of every setting in this menu will be given below: Item Description Video Resolution Specify video resolution of MPEG4 video encoder. VGA resolution provides more details than QVGA, but requires more network bandwidth. There are two video quality types: CBR (Constant Bit Rate), and VBR (Variable Bit Rate): CBR: The video bit rate is fixed, you can select a bit rate from dropdown menu. But if your network bandwidth is limited, select a lower bit rate will help. VBR: Video bit rate is variable based on the video content being transferred. There're 5 levels of setting from `Lowest' to `Highest'. Select `Lowest' will lower video quality and save network bandwidth; Video Frame Rate if a better video quality is required, select `High' or `Highest'. Higher video refresh rate provides more details about motion, but requires more network bandwidth. CAUTION: Choosing a low frame rate will save bandwidth, but may not be able to capture every motion if the object that IP camera points to is moving too fast. Click `Apply' to save settings and make the new settings take effect. 3. 4. 3 MJPEG If you selected `MJPEG' as the video encoding format of this IP camera, you can specify the parameters of the MJPEG video encoder here. The descriptions of every setting in this menu will be given below: Item Description Video Resolution Specify video resolution of MJPEG video encoder. VGA resolution provides more details than QVGA and QQVGA, but requires more network bandwidth. Higher video quality provides better video quality, but requires more network bandwidth. Higher video Rate refresh rate provides more details about motion, but requires more network bandwidth. CAUTION: Choosing a low frame rate will save bandwidth, but may not be able to capture every motion if the object that IP camera points to is moving fast. Click `Apply' to save settings and make the new settings take effect. 3. 6 Motion Detection Basic Settings 3. 6. 1 The motion detection function makes this IP camera become your non-stop guard. You don't have to waste all the time monitoring the images from the camera, and camera will detect all motions for you. Once motion is detected, a captured image will be sent to you by Email or via FTP. You can access this menu by clicking `Video Setup' on the top of web management interface, and opening the 'Motion Detection' tab. The descriptions of Item Motion Detection Enable Detection Interval every setting in this menu will be given below: Description Select `Enable' to start motion detection, and select `Disable' to disabled it. If a motion is detected after last detection time, and before next detection time, nothing will be send by Email or via FTP. If the time interval is too long, you may not be able to know what is happened between time interval; if the time interval is too short, you may receive too much unnecessary images, and consumes too much disk Mail snapshot E-Mail Subject Send snapshot file to FTP storage spaces on Email and / or FTP server. Select `Yes' to send a picture to the Email address you specified in `E-Mail & FTP' menu when a motion is detection, and select `No' to disable this function. [. . . ] Please confirm the IP address setting of the computer you're using. If they're not in the same subnet, they will not be able to communicate with each other. Please make the IP address you used to connect to the IP camera is correct. If you forget the IP address of the IP camera, you will have to reset it to factory default value (which is 192. 168. 0. 231) by pressing `reset' button at the bottom of the IP camera. [. . . ]