User manual SKIL 7240

[. . . ] 3) PERSONAL SAFETY a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. [. . . ] g) Use the power tool, accessories and tool bits etc. , in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5) SERVICE a) Have your power tool serviced by a qualified repair person using only identical replacement parts. SAFETY INSTRUCTIONS FOR SANDERS Avoid damage that can be caused by screws, nails and other elements in your workpiece; remove them before you start working Always keep the cord away from moving parts of the tool; direct the cord to the rear, away from the tool When you put away the tool, switch off the motor and ensure that all moving parts have come to a complete standstill Use completely unrolled and safe extension cords with a capacity of 16 Amps (U. K. 13 Amps) In case of electrical or mechanical malfunction, immediately switch off the tool and disconnect the plug We recommend to use original SKIL-accessories as listed at the back of this instruction manual This tool should not be used by people under the age of 16 years The noise level when working can exceed 85 dB(A); wear ear protection If the cord is damaged or cut through while working, do not touch the cord, but immediately disconnect the plug Never use the tool when cord is damaged; have it replaced by a qualified person Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool (tools with a rating of 230V or 240V can also be connected to a 220V supply) This tool is not suitable for wet sanding Do not work materials containing asbestos (asbestos is considered carcinogenic) Dust from material such as paint containing lead, some wood species, minerals and metal may be harmful (contact with or inhalation of the dust may cause allergic reactions and/or respiratory diseases to the operator or bystanders); wear a dust mask and work with a dust extraction device when connectable Certain kinds of dust are classified as carcinogenic (such as oak and beech dust) especially in conjunction with additives for wood conditioning; wear a dust mask and work with a dust extraction device when connectable Follow the dust-related national requirements for the materials you want to work with When sanding metal, sparks are generated; do not use dustbag/dustbox and keep other persons and combustible material from work area Do not touch the moving sanding sheet Do not continue to use worn, torn or heavily clogged sanding sheets Wear protective gloves, safety glasses, close-fitting clothes and hair protection (for long hair) Always disconnect plug from power source before making any adjustment or changing any accessory WHEN CONNECTING NEW 3-PIN PLUG (U. K. ONLY): Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal of the plug If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not left unattended USE Mounting of sanding sheet 4 !perforation in sanding sheet should correspond with perforation in sanding foot !always use the tool with the total sanding surface covered with sanding paper - mount VELCRO sanding sheet as illustrated Mounting support plate 5 - remove VELCRO sanding sheet - remove delta tip A while pushing button B - mount support plate C as illustrated Mounting special sanding attachments 6 - mount desired sanding attachment to support plate C as illustrated - mount corresponding VELCRO sanding sheet to sanding attachment - 3 sanding positions Mounting "Louvre" attachment 7 - remove VELCRO sanding sheet - remove delta tip A while pushing button B - mount "Louvre" attachment as illustrated Dust suction 8 - mount dustbox E/dustbag E 8 - empty dustbox E/dustbag E regularly for optimal dust pick-up performance !do not use dustbox/dustbag when sanding metal On/off switch - switch on/off the tool by pushing switch F 2 forward/backwards !before the sanding surface reaches the workpiece, you should switch on the tool !before switching off the tool, you should lift it from the workpiece Spot light 9 (7208) Spot light G automatically lights on when activating switch F Holding and guiding the tool 0 !ZAJ/REZGS Az EN 60 745 alapjn vgzett mrsek szerint ezen kszlk hangnyoms szintje 71 dB(A) a hangteljestmny szintje 82 dB(A) (norml eltrs: 3 dB), a rezgsszm 14, 3 m/s2 (kzre-hat rtk; szrs K = 1, 5 m/s2). A miszaki dokumentci a kvetkezOE helyen tallhat: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. CZ CE STRVZUJC PROHLEN Potvrzujeme na odpovdnost, e tento vrobek odpovd nsledujcm normm nebo normativnm podkladm: EN 60 745, EN 55 014, podle ustanoven smrnic 2006/95/ES, 2004/108/ES, 98/37/ES (do 28. 12. 2009), 2006/42/ES (od 29. 12. 2009). HLUNOSTI/VIBRAC Meno podle EN 60 745 in tlak hlukov vlny tohoto pstroje 71 dB(A) a dvka hlunosti 82 dB(A) (standardn odchylka: 3 dB), a vibrac 14, 3 m/s2 (metoda ruka-pae; nepfiesnost K = 1, 5 m/s2). Technick dokumentace u: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. TR CE STANDARDIZASYON BEYANI Yeane sorumlu olarak, bu rnn aflaidaki standartlara veya standart belgelerine uygun olduunu beyan ederiz: EN 60 745, EN 55 014, ynetmelii hkmleri uyarinca 2006/95/EG, 2004/108/EG, 98/37/EG (28. 12. 2009 tarihine kadar), 2006/42/EG (29. 12. 2009 tarihinden itibaren). / GRLT/T<TREfiIM llen EN 60 745 gre ses basinci bu makinanin seviyesi 71 dB(A) ve al>flma s>ras>ndaki grlt 82 dB(A) (standart sapma: 3 dB), ve titreflim 14, 3 m/s2 (el-kol metodu; tolerans K = 1, 5 m/s2). Teknik belgelerin bulunduu merkez: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. PL OWIADCZENIE ZGODNOCI CE Niniejszym owiadczamy ponoszc osobist odpowiedzialno, e produkt wykonany jest zgodnie z nastpujcymi normami i dokumentami normalizujcymi: EN 60 745, EN 55 014, z godnie z wytycznymi 2006/95/EU, 2004/108/EU, 98/37/EU (do 28. 12. 2009), 2006/42/EU (od 29. 12. 2009). HAASU/WIBRACJE Pomiarw dokonano zgodnie z norm EN 60 745 cinienie akustyczne narzdzia wynosi 71 dB(A) za poziom mocy akustycznej 82 dB(A) (poziom odchylenie: 3 dB), za wibracje 14, 3 m/s2 (metoda do-rka; bd pomiaru K = 1, 5 m/s2). Dokumentacja techniczna: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. RU , : EN 60 745, EN 55 014, 2006/95/EC, 2004/108/EC, 98/37/EC ( 28. 12. 2009), 2006/42/EC ( 29. 12. 2009). / co o EN 60 745 71 (A) e - 82 (A) ( : 3 dB), 14, 3 /2 ( ; K = 1, 5 /2). CE , : EN 60 745, EN 55 014, 2006/95/EG, 2004/108/EG, 98/37/EG 28. 12. 2009 p. ), 2006/42/EG ( 29. 12. 2009 p. ). / EN 60 745 71 () i 82 () ( : 3 ), i 14, 3 /2 ( ; K = 1, 5 /2). [. . . ] Tehnika dokumentacija se moe dobiti kod: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. SRB CE IZJAVA O USKLA ENOSTI Pod punom odgovornou izjavljujemo da je ovaj proizvod usklaen sa sledeim standardima ili standardizovanim dokumentima: EN 60 745, EN 55 014, u skladu sa odredbama smernica 2006/95/EG, 2004/108/EG, 98/37/EG (do 28. 12. 2009), 2006/42/EG (od 29. 12. 2009). BUKA/VIBRACIJE Mereno u skladu sa EN 60 745, nivo pritiska zvuka ovog alata iznosi 71 dB(A), a jaina zvuka 82 dB(A) (normalno odstupanje: 3 dB), a vibracija 14, 3 m/s2 (mereno metodom na aci-ruci; nesigurnost K = 1, 5 m/s2). Tehnika dokumentacija kod: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. SLO IZJAVA O USTREZNOSTI CE Odgovorno izjavljamo, da je ta izdelek v skladu z naslednjimi standardi ali standardnimi dokumenti: EN 60 745, EN 55 014, v skladu s predpisi navodil 2006/95/ES, 2004/108/ES, 98/37/ES (do 28. 12. 2009), 2006/42/ES (od 29. 12. 2009). HRUP/VIBRACIJA Izmerjeno v skladu s predpisom EN 60 745 je raven zvonega pritiska za to orodje 71 dB(A) in jakosti zvoka 82 dB(A) (standarden odmik: 3 dB), in vibracija 14, 3 m/s2 (metoda `dlan-roka'; netonost K = 1, 5 m/s2). [. . . ]