User manual SKIL F0155255AH

[. . . ] Com 7 Circular saw INTRODUCTION 5255 ? This tool is intended for lengthways and crossways cutting of wood with straight cuts as well as angle cuts up to 45; with the appropriate saw blades also non-ferrous metals, light building materials and plastics can be cut ? This tool is not intended for professional use ? Read and save this instruction manual 2 TECHNICAL DATA 1 SAFETY GENERAL SAFETY INSTRUCTIONS WARNING!Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. in the warnings refers to your mainsoperated (corded) power tool or battery-operated (cordless) power tool. B) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. [. . . ] C) Lower guard should be retracted manually only for special cuts such as plunge cuts and compound cuts. Raise lower guard by retracting handle and as soon as blade enters the material, the lower guard must be released. D) Always observe that the lower guard is covering the blade before placing saw down on bench or floor. An unprotected, coasting blade will cause the saw to walk backwards, cutting whatever is in its path. Be aware of the time it takes for the blade to stop after switch is released. When bevel cutting, cutting depth does not correspond with value on cutting depth scale ? 90 Cutting angle check 5 - adjust and tighten foot K to maximum cutting depth 4 - adjust and tighten cutting angle to 0 - check for a 90 angle between the blade and bottom of foot with a square - if adjustment is needed, loosen knob M and use adjustment screw P as illustrated ? Adjustable saw line visor Q 6a - for guiding tool along desired line of cut marked on the workpiece - for a straight 0 cut or a 45 bevel cut use the indicator line concerned !The wide part of the foot should rest on the supported part of the workpiece - can be adjusted to allow you to choose whether waste material is on inner or outer side of blade 6b !Cutting width is determined by width of blade teeth and not by width of blade body !Always make trial cuts first to verify actual line of cut ? Dust suction - connect vacuum cleaner to extension R 7 !Never let the vacuum cleaner hose interfere with the lower guard or the cutting operation - one may also use a dust bag (SKIL accessory 2610387402) ? Operating the tool 7 - connect plug to power source - always hold handle S firmly with one hand and handle T firmly with the other hand - place tool with front end of foot flat on workpiece !Ensure that the saw teeth are not engaged into the workpiece - switch on tool by first pressing knob V (= safety switch which cannot be locked) and then pulling trigger W !The tool should run at full speed before the blade enters into the workpiece - lower guard F opens automatically when saw blade enters the workpiece (open lower guard manually by using lever G only for special cuts such as plunge cuts) !Do not force the tool (apply light and continuous pressure in order to avoid overheating the blade tips and, in case of cutting plastics, melting the plastic material) !While working, always hold the tool at the grey-coloured grip area(s) - after completing the cut switch off tool by releasing trigger W !Ensure that the blade has come to a complete standstill, before you lift the tool from the workpiece ? Plunge cutting 0 - set desired cutting depth - tilt tool forward with saw line visor Q lined up with desired line of cut marked on the workpiece - open lower guard F with lever G - just before blade enters workpiece, switch on tool and gradually lower back end of tool using front end of foot as hinge-point - gradually move tool downward as well as forward - as soon as blade enters the material, release lever G !- support panel close to the cut either on floor, table or workbench !Set cutting depth so that you cut through panel and not through support - in case parallel guide does not allow desired width of cut, clamp or nail straight piece of wood to workpiece as a guide, and use the right side of the foot against this guide MAINTENANCE / SERVICE ? This tool is not intended for professional use ? Always keep tool and cord clean (especially the ventilation slots) !Disconnect the plug before cleaning ? Always keep the area around lower guard F 3 clean (remove dust and chips by blowing out with compressed air or with a brush) ? Clean saw blade immediately after use (especially from resin and glue) ? If the tool should fail despite the care taken in manufacturing and testing procedures, repair should be carried out by an after-sales service centre for SKIL power tools - send the tool undismantled together with proof of purchase to your dealer or the nearest SKIL service station (addresses as well as the service diagram of the tool are listed on www. 2013 NOISE/VIBRATION ? Measured in accordance with EN 60745 the sound pressure level of this tool is 97 dB(A) and the sound power level 108 dB(A) (standard deviation: 3 dB), and the vibration ?2 m/s ? The vibration emission level has been measured in accordance with a standardised test given in EN 60745; it may be used to compare one tool with another and as a preliminary assessment of exposure to vibration when using the tool for the applications mentioned - using the tool for different applications, or with different or poorly maintained accessories, may significantly increase the exposure level - the times when the tool is switched off or when it is running but not actually doing the job, may significantly reduce the exposure level !hnfr sig till ntdrivna elverktyg (med ntsladd) och till batteridrivna elverktyg (sladdlsa). Sgklingor som inte passar till sgens monteringskomponenter roterar orunt och leder till att kontrollen frloras ver sgen. [. . . ] de praf ?i lucra?i cu un dispozitiv de extragere a prafului cnd poate fi conectat ? Anumite tipuri de praf sunt clasificate ca fiind cancerigene (cum ar fi praful de stejar ?i fag) n special n combina?ie cu aditivi pentru tratarea lemnului; purta?i o masc?de praf ?i lucra?i cu un dispozitiv de extragere a prafului cnd poate fi conectat ? Respecta?i reglement?rile na?ionale referitoare la aspira?ia prafului n func?ie de materialele de lucru folosite ? Folosi?i doar o mas?repornirea motorului dupa ntreruperea tensiunii ? Folosi?i doar o mas?sunt folosite accesoriile originale ? Folosi?i numai accesoriile a c?ror tura?ie admis? [. . . ]