User manual SONY VPCEG1BFX

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SONY VPCEG1BFX. We hope that this SONY VPCEG1BFX user guide will be useful to you.


SONY VPCEG1BFX : Download the complete user guide (2108 Ko)

Manual abstract: user guide SONY VPCEG1BFX

Detailed instructions for use are in the User's Guide.

[. . . ] Product failure due to improper installation is not covered under the Warranty. The installer must perform a ground continuity check on the power outlet box before beginning the installation to insure that the outlet box is properly grounded. If not properly grounded, or if the outlet box does not meet electrical requirements noted (under ELECTRICAL REQUIREMENTS), a qualified electrician should be employed to correct any deficiencies. CAUTION: For personal safety, remove house fuse or open circuit breaker before beginning installation to avoid severe or fatal shock injury. [. . . ] • This microwave oven is for installation over ranges up to 36” wide. €¢ If you are going to vent your microwave oven to the outside, see Hood Exhaust Section for exhaust duct preparation. €¢ When installing the microwave oven beneath smooth, flat cabinets, be careful to follow the instructions on the top cabinet template for power cord clearance. 16½” 30” 2” 66” or More from the Floor to the Top of the Microwave 7 DE68-03587B-EN. Remove the installation instructions, Exhaust adaptor, filters, glass tray and the small hardware bag. Screws Screws Mounting Plate the wall with a small nail to find the edges of the stud. The center of any adjacent studs should be 16” or 24” from this mark. This plate will be used as the rear wall template and for mounting. NOTE: You will have to reuse two screws in original location of outcase after removing mounting plate. DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET Plate position – beneath flat bottom cabinet Plate position – beneath framed recessed cabinet bottom 16-1/2" C L At least 30 Draw a vertical line on the wall at the center of the 30 wide space. Tape the Rear Wall Template onto the wall matching the centerline and touching the bottom of the cabinet. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor. Insert the bolts into the mounting plate through the To use toggle bolts: Spacing for Toggles More Than Wall Thickness Mounting Plate Toggle Wings Toggle Bolt holes designated to go into drywall and reattach the toggle wings to ¾” onto each bolt. Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate. €¢ Drill the holes, following the instructions on the TOP CABINET TEMPLATE. CAUTION: Wear safety goggles when drilling holes in the cabinet bottom. NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord. NOTE: We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf. IMPORTANT: If filler blocks are not used, case damage may occur from over tightening screws. NOTE: When mounting the microwave oven, thread power cord through hole in bottom of top cabinet. Make sure tape securing damper is removed and damper pivots easoly before mounting microwave. CAUTION: You will need to make adjustments to assure proper alignment with your house exhaust duct after the microwave is installed. [. . . ] PREPARING THE REAR WALL FOR OUTSIDE BACK EXHAUST You need to cut an opening in the rear wall for outside exhaust. C L • Read the instructions on the REAR WALL TEMPLATE. €¢ Cut the opening, following the instructions of the REAR WALL TEMPLATE. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SONY VPCEG1BFX




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SONY VPCEG1BFX will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.