User manual WHIRLPOOL AWM 8121 INSTRUCTION FOR USE

[. . . ] INSTRUCTIONS FOR USE BEFORE USING THE WASHING MACHINE FIRST WASH CYCLE PRECAUTIONS AND GENERAL RECOMMENDATIONS DESCRIPTION OF THE WASHING MACHINE CHILD SAFETY DETERGENTS AND ADDITIVES WASHING PROGRAMME REMOVING THE FILTER DRAINING RESIDUAL WATER CARE AND MAINTENANCE TROUBLESHOOTING GUIDE AFTER-SALES SERVICE TRANSPORT AND HANDLING INSTALLATION BEFORE USING THE WASHING MACHINE 1. Removing the packaging and check • After unpacking, make sure that the washing machine is undamaged. • Keep the packaging materials (plastic bags, polystyrene parts, etc. ) out of reach of children, as they are potentially dangerous. 6. Electrical connections • Electrical connections must be carried out by a qualified technician in compliance with the manufacturer's instructions and current standard safety regulations. • Voltage information, power consumption and electrical protection data are supplied on the inside of the appliance door. • The appliance must be connected to the mains exclusively by means of a socket with an earth connection in accordance with established regulations. [. . . ] For this programme do not add any further detergent. Programme interruption or pause To interrupt the running programme for a certain period and continue it at a later time: 1. 2. Following the desired pause press the “Start/Pause” button once again. Cancelling the programme If the current programme is to be terminated prematurely and cancelled, the water must be pumped out first before the door can be opened: 1. The spin indicator shows “0” and the remaining time indicator (if available) shows “0:02” minutes. Disengage the detergent dispenser by pressing the release lever in the prewash compartment and lately remove the drawer. 2. Remove the inserts softener compartment, the insert for liquid detergents and the siphon from the chlorine bleach compartment, (if available, four chambers model “A”). Do not operate washing machine with the detergent drawer removed. A Water hose mesh filter Check and clean periodically. 6. Remove the filter from the washing machine with pliers and clean it. 7. Replace the filter and screw the hose connection back on to the machine. 8. Turn on the tap and ensure that the connections are completely water-tight. A For machines with Water Stop hose “B” 1. 5. Turn on the tap and ensure that the connection is completely water-tight. B Home Appliances TROUBLESHOOTING GUIDE This washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage and react appropriately. Often, however, the faults detected are small enough to be solved in a matter of minutes. For example: Detergent and additive product residues in dispenser at end of wash. Check whether: • the siphon is correctly installed and clean (see “Care and Maintenance”); • enough water is being supplied. The mesh filters between the inlet hose and the tap could be clogged (see “Care and Maintenance”). Check and clean the filter two or three times a year (see “Removing the filter”). The appliance will not start, no lamp lights up. Check whether: • the appliance is plugged in; • the wall socket is functioning correctly (use a table lamp or similar); • a programme is selected correctly. The appliance vibrates during the spin cycle. Check whether: • the appliance is levelled and solidly installed on all four feet (see “Installation Instructions”); • the transit bolts have been removed. The transit bolts must be removed before the appliance can be used (see “Installation Instructions”). The appliance will not start, but the “Start/Pause” lamp is flashing. Check whether: • the appliance door is properly closed (child safety); • the programme has been changed; • the water tap is open. If not, open the tap and press the “Start/Pause” button. Final spin results are poor: The appliance has an imbalance detection and correction system. If individual heavy articles are loaded (bathmat, bathrobe, etc. ) this system may reduce the spin speed automatically to protect the appliance or even interrupt the spin cycle altogether, if the imbalance is too great even after several spin starts. • If the laundry is still too wet at the end of the cycle, add smaller articles of laundry to balance the load and repeat the spin cycle. Ensure correct amount of detergent is used The appliance stops during the programme. Check whether: • the “Rinse Hold” lamp is on, terminate this option by pressing the button again; • another programme has been selected. Reselect the desired programme and press the “Start/Pause” button; • “Start/Pause” lamp is flashing. Press “Start/ Pause” button; • Safety system of the appliance was activated. See fault description table. No water or insufficient water supply: • the appliance has a safety hose and the safety valve has opened (red indicator in the safety valve inspector window). [. . . ] The appliance can be connected without an anti-backpressure valve. A For models with Water Stop hose “B” If the flexible hose is damaged, unplug the appliance from the mains immediately. 2. Check water-tightness of tap and appliance connections by turning the tap completely on. If the hose is too short, replace it with a 3 m Water Stop hose (available from After-Sales Service or from your dealer). This operation must be carried out exclusively by a licensed electrician. [. . . ]