User manual WHIRLPOOL DWF 407 W INSTALLATION

[. . . ] • If necessary, the power cable may be replaced with one the same obtained from our After-Sales Service. For appliances with water-stop system: The water inlet hose and plastic casing contain electrical components. Load capacity: -12 place settings • • • EC Declaration of Conformity This appliance has been designed, constructed and distributed in compliance with the safety requirements of EC Directives: • 73/23/EC • 89/336/EC • 93/68/EC. ENERGY AND WATER SAVING TIPS • • Do not rinse crockery under running water. • If ecological energy sources are available such as solar panel heating, heat pumps or centralised heating systems, the appliance may be connected to the hot water mains up to a maximum temperature of 60°C. [. . . ] Consult your local Water Board or check your last water bill. • If the water hardness level exceeds category 1, before using the dishwasher for the first time, fill the salt container and run a wash cycle so that any excess saline solution discharged is immediately removed by the water to prevent corrosion. Important: Only use regeneration salts recommended for use in domestic dishwashers. Do not fill the salt container with detergent as this will cause irreparable damage to the water softener system. • • To fill the salt container: 1. If the dishwasher is new, fill the salt container to the rim with water. Screw the cap back on by turning it clockwise. Salt level indicator The green float is clearly visible in the cap window when the salt container is full. The green float lowers and is no longer visible when the salt container is empty. 82 HOW TO FILL THE RINSE AID DISPENSER The rinse aid facilitates drying and prevents the formation of unsightly spots and streaks on crockery. Before using the dishwasher for the first time, fill the rinse aid dispenser. Open the rinse aid dispenser by turning knob A counter-clockwise (see diagram) and pulling it out. Immediately wipe away any spilt rinse aid (from metal parts as well) to prevent excess suds which may spoil washing results. Rinse aid level indicator light = empty dark = full. How to adjust the rinse aid dosage regulator. (Open the cover and close again following adjustment). If you are not satisfied with washing or drying results, change the dial setting with a spoon handle or coin. • The power cable must only be replaced by a qualified technician. 84 CONNECTIONS 1) ELECTRICAL CONNECTIONS “Warning - this appliance must be earthed” This appliance is normally supplied with a mains lead having a plug fitted in the factory which has been checked for correct earth continuity. If the fitted plug is not suitable for your socket outlet, or if the machine’s mains lead is not fitted with a plug, you should fit a suitable new, good quality plug by following the instructions in (2) below. Any unsuitable plug should be cut off and disposed of in order to avoid a possible shock hazard should it be inserted into a socket. 2 pin with side earth contact) The wire which is coloured GREEN AND YELLOW must be connected to the earth contact. The other two wires should be connected to the two pins, irrespective of colour. 3) FUSE REPLACEMENT If the mains lead of this appliance is fitted with a BS 1363A 13 amp fused plug, replace the fuse only with an A. S. T. A. approved type conforming to BS 1362 and proceed as follows: 2) CONNECTION TO A REWIRABLE PLUG - to be carried out only by a qualified electrician The wires in the mains lead are coloured in accordance with the following code: BLUE - “NEUTRAL” (“N”) BROWN - “LIVE” (“L”) GREEN AND YELLOW - “EARTH” (“E”) To fit a new plug, proceed as follows: 2. 1 Polarized Plugs (e. g. The GREEN AND YELLOW wire must be connected to the terminal in the plug which is marked with the letter “E” or by the Earth symbol or coloured yellow or green and yellow. The BLUE wire must be connected to the terminal which is marked with the letter “N” or coloured black. The BROWN wire must be connected to the terminal which is marked with the letter “L” or coloured red. For all other types of plug, the supply socket should be protected by a 16 A fuse or circuit breaker at the distribution board 85 MAINTENANCE AND CLEANING Before cleaning or carrying out maintenance, switch off the appliance, disconnect the mains plug. [. . . ] Regularly wipe the door seal and inside of the door with a damp cloth to remove any food residues. If the spray nozzles become clogged with food residues (clean the spray arms as follows). The spray jets must point upwards. Cleaning the soil filter: If necessary, the filter can be cleaned after each wash programme as follows: 1. Reassemble and reposition. 86 TROUBLESHOOTING GUIDE If a fault occurs, before contacting our After-Sales Service, make the following checks to try and remedy the problem. Restart the wash programme to see if the fault repeats: • Press the On/Off button or push and pull the program knob to restart the programme. If the malfunction persists, switch off the appliance and turn off the water tap. [. . . ]